Viking BRTGK72SS - Manual (Page 5)

5
REFRIGERATOR INSTALLATION
U Usse e ttw wo o o orr m mo orre e p pe eo op plle e tto o m mo ovve e aan nd d iin nssttaallll
rre effrriig ge erraatto orr.. F Faaiillu urre e tto o ffo ollllo ow w tth hiiss iin nssttrru uccttiio on n ccaan n
rre essu ulltt iin n b baacckk o orr o otth he err iin njju urryy.. T To o aavvo oiid d p pe errsso on naall
iin njju urryy,, w we eaarr g gllo ovve ess w wh he en n p pe errffo orrm miin ng g aan nyy
iin nssttaallllaattiio on n p prro occe ed du urre e aan nd d w we eaarr e eyye e p prro otte eccttiio on n
w wh he en n ccu uttttiin ng g m me ettaall ssttrraap pss..
M Mo osstt o off tth he e rre effrriig ge erraatto orr’’ss w we eiig gh htt iiss aatt tth he e tto op p.. E Exxttrraa ccaarre e iiss n ne ee ed de ed d w wh he en n m mo ovviin ng g tth he e rre effrriig ge erraatto orr tto o p prre evve en ntt ttiip pp piin ng g..
D Do o N No ott rre em mo ovve e p prro otte eccttiivve e ffiillm m u un nttiill rre effrriig ge erraatto orr iiss iin n o op pe erraattiin ng g p po ossiittiio on n.. A Allll ffo ou urr lle evve elliin ng g rro olllle errss m mu usstt cco on nttaacctt tth he e ffllo oo orr
tto o ssu up pp po orrtt aan nd d ssttaab biilliizze e tth he e ffu ullll w we eiig gh htt.. D Do o n no ott d drro op p rre effrriig ge erraatto orr..
1. Remove exterior shipping materials prior to moving
refrigerator into home. Remove top and bottom strap (see
Figure 1).
2. Remove top cap (see Figure 1).
3. Cut carton rear approximately 1/4” (.64 cm) to 1” (2.5 cm)
from right corner (see Figure 2) with a utility knife extended
1/4” (.6 cm). Remove carton, exterior packaging, and lag
screw tape. Save cardboard shipping
material to protect floor surface when
installing refrigerator. Do not remove nylon
cord from power cord. Remove anti-tip
board, lag screws, door trim insert, and
kickplate from rear of refrigerator (see
Figure 3).
4. Remove shipping brackets from skid by
removing 4 bolts (2 each side) with a 7/16”
socket head screwdriver (see Figure 4).
•Tilting refrigerator is not required to
remove shipping brackets.
5. Slip cart between
refrigerator and skid.
Remove refrigerator
from skid. Use excess
packaging to protect
decorative trim. Verify
that leveling legs are
up (0” adjustment)
(see Figure 5).
6. To avoid floor damage,
use protective material (see Figure 6).
T TIIP P O OV VE ER R H HA AZ ZA AR RD D
R Re effrriig ge erraatto orr iiss tto op p h he eaavvyy aan nd d ttiip pss e eaassiillyy
w wh he en n n no ott cco om mp plle ette ellyy iin nssttaalllle ed d.. K Ke ee ep p
d do oo orrss ccllo osse ed d u un nttiill rre effrriig ge erraatto orr iiss
cco om mp plle ette ellyy iin nssttaalllle ed d aan nd d sse eccu urre ed d w wiitth h
llaag g b bo ollttss tto o rre eaarr w waallll..
U Usse e ttw wo o o orr m mo orre e p pe eo op plle e tto o m mo ovve e aan nd d
iin nssttaallll rre effrriig ge erraatto orr.. F Faaiillu urre e tto o d do o sso o ccaan n
rre essu ulltt iin n d de eaatth h o orr sse erriio ou uss iin njju urryy..
Figure 1
Figure 2
Figure 3 Figure 4
Figure 5
Figure 6
K KIIC CK KP PLLA AT TE E
BACK VIEW
SKID
ANTI-TIP BOARDS
AND LAG SCREWS