Viking F20050 EN - Manual (Page 5)

9 8
C CU US ST TO OM M W WO OO OD D F FR RA AM ME E IIN NS ST TA AL LL LA AT TIIO ON N IIN NS ST TR RU UC CT TIIO ON NS S
((D DF FU UW W M Mo od de ell))
Note: Weight of wood panel must not exceed 20 lbs.
W Wo oo od d S Sccrre ew wss
1. A #10 pan head wood screw should be used to properly secure the wood frame. A total of 10 screws will be needed.
2. Only use pan head screws.
3. DO NOT select a screw that is longer than the wood thickness at
the screw locations.
4. Use recommended pilot holes for the frame material. (See chart)
W Wo orrkkiin ng g M Ma atte erriia all W Wo oo od d S Sccrre ew w S Siizze e # #1 10 0
Hardwood 3/32 (0.24 cm)
Softwood 5/64 (0.20 cm)
A Asssse em mb blliin ng g D Do oo orr H Hiin ng ge e B Brra acckke ettss
(Disregard if hinge brackets are already attached)
1. Attach the top and bottom door hinge brackets to the door with the #10-32 machine screws and a 1/8” allen head
driver as shown in Figure 1 below.
2. Press in the shoulder bushings to the top and bottom door hinge brackets. Make certain that the shoulder is to the
outside of the door as shown in Figure 1 below.
3. Test fit the door to the unit to make certain door will hang correctly. The door is hung correctly when the top of the
door is parallel to the top of the unit. (See Figure 2) Adjustments can be made by loosening the door hinge
machine screws and moving the door hinge brackets on the door.
4. Tighten all four (4) machine screws after adjustments have been made.
5. Remove the door from the unit by removing the units top hinge set screw and angling the door off of the bottom
hinge pin.
Figure 1
Shoulder Bushing
Door Hinge Bracket
#10-32 Machine
Screw
Door Hinge
Screw Holes
Door Front
Surface
T Tyyp piicca all T To op p a an nd d B Bo otttto om m
D Do oo orr H Hiin ng ge e B Brra acckke ett
A Asssse em mb bllyy
Figure 2
This surface parallel to the unit.
(Right hinge door shown.)
Selecting and Preparing the Wood Frame - 15” W. DFUW Model
F FO OR R A A 3 3--1 1//2 2” ” T TO OE E K KIIC CK K
((C CO OV VE ER RS S T TH HE E E EN NT TIIR RE E D DO OO OR R E EX XT TR RU US SIIO ON N))
((L LE EF FT T H HIIN NG GE E))
1/4” X 3/8” Deep hinge screw clearance hole
-Locate and drill using door hinge hole after the door has been aligned
to the unit and when the wood is positioned on door.
1/4” X 3/8” Deep hinge screw clearance hole. Locate and drill using
door hinge hole after the door has been aligned to the unit and
when the wood is positioned on door.
Mounting surface
(Non-face) side
Mounting surface
(non-face) side
Mounting surface
(non-face) side
Min. 5/8” (1.7 cm)
Max. 3/4” (1.9 cm)
14 5/16”
(36.4 cm)
7 5/32” (18.2 cm)
23/32”
(1.8 cm) TYP
1 23/32” (4.4) cm min.
width to cover door
extrusion
23/32”
(1.8 cm)
TYP
BA
CK
VI
EW
O
F
OV
ER
LA
Y P
AN
EL
30 5/16”
(77.0 cm)
Pre-drilled pilot holes -
8 places
7 13/16”
(19.8 cm)
TYP
15 5/32”
(38.5 cm)
TYP
22 1.2”
(57.2 cm)
TYP
13/16” (2.1 cm)
counterbore 7/16”
(1.1 cm) deep
15/32” (1.2 cm)
Dia. hole
15./2” (1.2 cm)
3 7/32”
(8.1 cm)