3 bill of materials, 4 reference, Table 3–1. bill of materials – Texas Instruments bq24010/2 User Manual
Page 18
Bill of Materials
3-5
Schematic, Physical Layouts, and Bill of Materials
3.3
Bill of Materials
Table 3–1 lists materials required for the EVM.
Table 3–1. Bill of Materials
Item#
bq24010
–1
bq24012
–2
Ref
Des
Description
Size
MFR
Part Number
1
0
0
C1
Capacitor, ceramic, X5R,
1
µ
F, 10 V
805
Panasonic
ECJ-2YB1A105K
2
1
1
C2
Capacitor, ceramic, X5R,
1
µ
F, 10 V
805
Panasonic
ECJ-2YB1A105K
3
1
1
C3
Capacitor, ceramic, X7R,
0.47
µ
F, 16 V
805
Panasonic
ECJ-2YB1C474K
4
1
1
D1
Diode, LED, red, 1.8 V,
20 mA, 20 mcd
603
Lite-On
160-1181-1-ND
5
2
2
D2, D3
Diode, LED, green, 2.1 V,
20 mA, 6 mcd
603
Lite-On
160-1183-1-ND
6
1
1
J1
Terminal block, 2 pin, 6 A,
3,5 mm
0.27
×
0.25
OST
ED1514
7
2
2
J2, J3
Terminal block, 4 pin, 6 A,
3,5 mm
0.55
×
0.25
OST
ED1516
8
3
3
J4, J5,
J6
Header, 3 pin, 100 mil
spacing, (36-pin strip)
0.100
×
3
Sullins
PTC36SAAN
9
3
3
R1, R2,
R5
Resistor, chip, 1.5 k
Ω
,
1/16 W, 1%
603
Std
Std
10
2
0
R3, R6
Resistor, chip, 1 M
Ω
,
1/16 W, 1%
602
Std
Std
11
0
1
R6
Resistor, chip, 10 k
Ω
,
1/16 W, 1%
603
Std
Std
12
1
1
R4
Resistor, chip, 1.3 k
Ω
,
1/16 W, 1%
603
Std
Std
13
1
0
U1
IC, single Li-Ion/Li-Poly,
charge manager
MLP10
TI
bq24010DRC
14
0
1
U1
IC, single Li-Ion/Li-Poly,
charge manager
MLP10
TI
bq24012DRC
15
3
3
—
Shunt, 100-mil, black
0.100
3M
929950-00
16
1
1
—
PCB, bq24010/2,
1.6 in
×
1.3 in
×
0.031 in
Any
SLUP162
Notes:
1) These assemblies are ESD sensitive; ESD precautions must be observed.
2) These assemblies must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.
3) These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4) Reference designators marked with an asterisk (**) cannot be replaced by substitutes. All other components can
be replaced with equivalent manufacturer components.
3.4
Reference
1) bq2401x data sheet (SLUS530)