English – Toastmaster TC17A User Manual
Page 3
3
ENGLISH
C. Shutdown Procedure
1.
Switch the ON/OFF/STBY knob to the OFF (O) position.
2.
Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
3.
AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
D. Clearing Jams
WARNING
NEVER INSERT YOUR HANDS INTO THE TOASTING
CHAMBER TO CLEAR A JAM. SERIOUS INJURY MAY
RESULT.
CAUTION
NEVER use a plastic object to clear a jam. If the toaster is not
completely cool, damage to the toaster may result.
CAUTION
When clearing a jam, use care to avoid damaging the heating ele-
ments.
1.
Switch the ON/OFF/STBY knob to the OFF (O) position.
2.
Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
3.
AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
CAUTION - HOT SURFACES
DO NOT ATTEMPT TO CLEAR THE JAM UNTIL THE
TOASTER HAS COOLED THOROUGHLY.
4.
Carefully clear the jam using a long object as a probe. This
object should preferably be made of wood, which is less likely
to damage the heating elements.
E. Daily Cleaning
WARNING
WHEN CLEANING THE TOASTER, NEVER APPLY
ENOUGH LIQUID TO STAND IN PLACE ON THE UNIT. DO
NOT SPRAY, RINSE, OR SUBMERGE THE TOASTER.
EXCESSIVE MOISTURE IN THE UNIT WILL CAUSE A SE-
VERE ELECTRICAL HAZARD AND MAY OTHERWISE
DAMAGE THE TOASTER.
CAUTION
DO NOT clean your toaster using abrasive cleaners or pads. Both
will scratch and dull the finish.
1.
With the conveyor running, use a brush to clean any crumbs off
the conveyor into the crumb tray.
2.
Switch the ON/OFF/STBY knob to the OFF (O) position.
3.
Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
4.
AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
CAUTION - HOT SURFACES
DO NOT TOUCH HOT SURFACES ON THE TOASTER, OR
REACH INTO THE TOASTING CHAMBER, UNTIL THE UNIT
HAS COOLED THOROUGHLY.
5.
Wipe the exterior of the toaster with a damp sponge or cloth
soaked in hot or warm detergent water. Wipe with a clean,
damp cloth to remove the excess detergent, and then wipe again
to dry the toaster.
6.
Remove the crumb tray and the return tray from the toaster,
and empty them. Wash the trays in warm detergent water, and
rinse them.
CAUTION
Never remove the crumb tray while the conveyor is moving.
7.
Remove the entry rack from the toaster. Wash the rack in warm
detergent water, and rinse it.
8.
Towel the trays and entry rack dry. Reassemble all parts onto
the toaster.
Load buns/bagels
CUT SIDE UP
for proper toasting
Figure 5
B. Operation Procedure
1.
Restore electrical power to the toaster at the circuit breaker/fused
disconnect.
2.
Switch the ON/OFF/STBY knob to the ON position.
3.
Allow the toaster to pre-heat for at least 15 minutes.
4.
Adjust the toasting time (if necessary) by turning the conveyor
speed control knob.
5.
Adjust the heating element temperatures (if necessary) by turning
the Top and Bottom temperature adjustment knobs.
NOTE: For proper toasting of one-sided bakery products (bagels,
etc.), we recommend the following:
Turn the Top temperature adjustment knob to the desired
setting to toast the cut side of the product.
Turn the Bottom temperature adjustment knob to a lower
setting, or to the OFF position, as desired.
Load the product onto the entry rack with the cut side facing
UP, as shown in Figure 5.
If the product is loaded cut-side down, reverse the Top and Bottom
temperature knob settings provided above. Note that if the product
is loaded cut-side down, the heat of the conveyor belt may cause
a slight streaking effect on the cut side of the bakery product.
5.
Load the entry rack with the bakery product to be toasted. The
product will slide off the entry rack and onto the conveyor.
6.
After toasting, remove the product from the return tray.
7.
During inactive periods, switch the Product Selection knob to the
STBY position. This reduces the power to the heating elements
to save power during idle periods and extends the life of the
toasters components. Switching the knob back to the ON position
will return the toaster to operating temperature within 5 minutes.
Bottom temperature
adjustment knob set to a
lower setting or to OFF
Top temperature
adjustment knob
set as desired