Toshiba 13A22 - Manual (Page 6)

6
MENU
VOL
–
SLEEP MUTE
CH RTN RECALL
VOL
+
ENTER
CH –
CH +
1 2 3
4 5 6
7
0
8 9
– SET +
1/2 CAP/TEXT
RESET
TV/VIDEO
POWER
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button on the remote
control. The clock will count down 10 minutes each time the
button is pressed in the order of 120, 110, 100, ······ 20, 10,
0. After the sleep time is programmed, the display will
disappear then reappear momentarily every ten minutes to
remind you the sleep timer function is operating. To confirm
the sleep time setting, press the SLEEP button once and the
remaining time will be momentarily displayed. To cancel
sleep time, press the SLEEP button repeatedly until the
display turns to 0.
5. VOL (VOLUME) + / – Buttons - Press the + button to
increase, or the – button to decrease the volume level.
6. MENU Button - Press to display the On-Screen menu
function.
7. SET + / – Buttons - Press to select the desired setting
during On-Screen operations.
8. RESET Button - Press to reset the On-Screen picture
adjustments to their factory preset positions.
9. TV/VIDEO Button - Switches between TV and external
inputs.
10. RECALL Button - When you press this button, the channel
number will appear in the upper right corner of the screen.
Press the button again to remove it from the screen.
11. MUTE Button - To turn off the sound, press this button
once. The TV will be silenced and the symbol MUTE will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL + or –
buttons.
12. CH (CHANNEL) + / – Buttons - Press the + button to
change to a higher numbered channel set into memory.
Press the – button to change to a lower numbered channel
set into memory.
13. ENTER Button - Press to enter or select information for On-
Screen operations.
14. 1/2 Button - Switches between Channel 1 and Channel 2 in
the Closed Caption mode.
15 . CAP/TEXT Button - Press this button to switch between
normal TV and the two Closed Caption modes (captions and
1/2 of full screen text). Closed Captioning will display text on-
screen for hearing impaired viewers.
REMOTE CONTROL
1. Open the battery compartment cover.
2. Install two "AAA" (penlight size) batteries.
HOW TO INSTALL BATTERIES
Before using the remote control, batteries must first be installed.
3. Replace the battery compartment cover.
1. POWER Button - Press to turn on the TV. Press again
to turn off the TV.
2. Direct Channel Selection Buttons (0-9) - Allows direct
access to any channel.
3. CH RTN Button - This button allows you to go back to the
previous channel selected by pressing the CH RTN
button. Press this button again to return to the channel you
were watching.
1
2
3
5
6
7
8
9
10
11
12
13
14
4
15
Use two "AAA" size penlight batteries (supplied) for the
transmitter. The batteries may last approximately one year
depending on how much the remote control is used. For
best performance, it is recommended that batteries should
be replaced on a yearly basis, or when the remote operation
becomes erratic. Do not mix old and new batteries or
different types.
BATTERY PRECAUTIONS
These precautions should be followed when using batteries
in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh
ones.
4. If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged;
they can overheat and rupture. (Follow battery
manufacturer's directions.)
3L11401B-E COVER-P07 3/6/2002, 18:18 6