Transition Networks E-MCC-1600 - Manual

COMPLIANCE INFORMATION
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Printed in the U.S.A. 33051.B
NOTE: Power Supply Modules can be “hot swapped”.
The E-MCC-PS MAY or MAY NOT be shipped with the Master/Slave switch
shown installed on the circuit board.
If present, the Master/Slave switch allows the Power Supply Module to be
configured as the primary (master) Power Supply Module or as the secondary
(slave) Power Supply Module.
If any Power Supply Module WITHOUT a Master/Slave switch is installed in the
E-MCC-1600 chassis, by default that Power Supply Module is secondary (slave).
If neither Power Supply Module has a Master/Slave switch, primary/secondary
status is automatic and non-configurable.
If both Power Supply Modules have Master/Slave switches and both are
configured as the primary (master) Power Supply Module, each Power Supply
Module contributes a portion of the power to the chassis (“load sharing”).
CAUTION: When installing a Power Supply Module that has a Master
/Slave switch in a chassis with a Power Supply Module that does not
have a Master/Slave switch, the Power Supply Module with the
Master/Slave switch MUST BE CONFIGURED AS PRIMARY (MASTER).
When installing two Power Supply Modules that have Master/Slave
switches, at least one Power Supply Module MUST BE CONFIGURED
AS PRIMARY (MASTER). Failure to observe this caution could result in
damage to, and subsequent failure of, Power Supply Module(s).
Minneapolis, MN 55344 USA
Optional AC Power Supply Module
for E-MCC-1600 Chassis
E-MCC-PS
INSTALLATION GUIDE
Master/Slave Switch
I 0
DECLARATION OF CONFORMITY
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model: Media Conversion Center AC Power Supply
Part Number: E-MCC-PS
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the E-MCC-PS to which this declaration refers is in
conformity with the following standards.
EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_April 8, 1999_____
Stephen Anderson, Vice-President of Engineering Date