Omega Vehicle Security 533i 3 - Manual (Page 16)

STATUS INDICATOR LIGHT
The Red Status Indicator Light visually confirms the status of the system and
provides a high level of visual deterrence. Additionally, the Status Indicator
Light is also part of the patented Automatic Transmitter Verification feature
and the Zone Violation Code feature. The Status Indicator Light, which
shares a housing assembly with the Valet Switch, is normally mounted in a
location where it can be easily seen by the driver, as well as from outside the
vehicle.
Security System Status: The primary function of the Status Indicator
Light is to indicate the status of the security system:
1) Off = The system is disarmed and not performing automatic functions.
2) On Constant = The system is in the Easy Valet Mode.
3) Flashing Slow = The system is fully armed.
4) Flashing Fast = Last Door Arming or Automatic Rearming is in progress.
Automatic Transmitter Verification: For the first 10 seconds after
the vehicle’s ignition is turned on, the Status Indicator Light will flash a
number of times equal to the number of transmitters that are capable of
operating the system:
5) 1 Flash /pause = 1 transmitter is programmed.
6) 2 Flashes /pause = 2 transmitters are programmed.
7) 3 Flashes /pause = 3 transmitters are programmed.
8) 4 Flashes /pause = 4 transmitters are programmed.
Zone Violation Code: If the system enters an alarm condition, the Red
Status Indicator Light will stop flashing slowly and begin to flash in
sequence to indicate which protected zone caused the alarm condition. The
Status Indicator Light will flash and pause to indicate which protected zone
was violated while the system is still armed, after it’s disarmed, and until the
vehicle’s ignition is turned on. The system’s Zone Violation Code circuit can
store two consecutive zone violations. If there have been multiple violations,
the Status Indicator Light will replay the two most recent violations in the
order in which they occurred.
9) 2 Flashes /Pause = System was triggered through the hood or trunk.
10) 3 Flashes /Pause = System was triggered through the door.
11) 4 Flashes /Pause = System was triggered by the sensor.
Note: Turning on the ignition will clear the Zone Violation Code.
Page 15
Sensors: The Crime Guard 533i 3 security system is equipped with a Dual-
Zone Infrasonic Impact Sensor to increase the effectiveness of the system.
The impact sensor is just one in a comprehensive line of available sensors.
Other available options are: glass tampering sensors, piezo shock sensors,
and microwave/radar sensors which can detect motion inside and outside the
vehicle. Your Crime Guard
dealer can provide details on the complete line
of sensors and help determine which sensor or sensors are best suited for your
needs.
- The system will automatically bypass the sensor zone if it is triggered five
times during a single armed period. If desired, this feature can be
programmed to not operate.
Prewarning Detection Circuit: When the sensor’s prewarn zone is
violated the security system will respond by chirping the siren three times
and relocking all of the doors.* If the prewarn circuit is triggered five times
while the system is armed, the circuit will automatically shutdown until the
security system is disarmed and armed again.
DUAL-ZONE IMPACT SENSOR
To Activate Remote Sensor Bypass:
First Arm the System, then within 4 Seconds Press &
Release the Small Lower Button.
THE SIREN WILL CHIRP TWICE TO
CONFIRM ARMING
THE SIREN THEN CHIRPS ONCE
TO CONFIRM SENSOR BYPASS
THE DOORS WILL LOCK
UPON ARMING*
THE PARKING LIGHTS
WILL FLASH TWICE
TO CONFIRM
ARMING
2
REMOTE SENSOR BYPASS
Remote Sensor Bypass allows the option of “turning off” the sensor any-
time the system is armed using the transmitter. When the sensor is by-
passed, only the sensor zone is bypassed and all other protected zones will
remain fully operational and vigilant. The sensor zone will reset to its nor-
mal operation the next time the system arms.
* An optional doorlock interface must be installed.
Page 16
1