Orion ATLAS 10 EQ 9874 - Manual (Page 18)

18
the finder scope to center it within the camera’s viewfinder.
Turn the motor drive on. Adjust the telescope’s focuser so
that the image appears sharp in the camera’s viewfinder. The
camera’s shutter is now ready to be opened. A remote shut‑
ter release must be used or the image will be blurred beyond
recognition. Try exposure times between 1 and 10 seconds,
depending upon the brightness of the planet to be photo‑
graphed and the ISO of the film being used.
“Piggyback Photography”
The Moon and planets are interesting targets for the bud‑
ding astrophotographer, but what next? Literally thousands
of deep‑sky objects can be captured on film with a type of
astrophotography called “piggybacking”. The basic idea is
that the camera with its own camera lens attached rides on
top of the main telescope. The telescope and camera both
move with the rotation of the Earth when the mount is polar
aligned and the motor drive is engaged. This allows for a long
exposure through the camera without having the object or
background stars blurred. An illuminated reticle eyepiece will
also be needed. The T‑ring and camera adapter are not need‑
ed, since the camera is exposing through its own lens. Any
camera lens with a focal length between 35mm and 400mm
is appropriate.
On the top of one of the tube rings is a piggyback camera
adapter. This is the black knob with the threaded shaft pro‑
truding through it. The tube ring with the piggyback adapter
should be closest to the open end of the telescope tube.
Remove the tube rings from the equatorial mount and swap
their position if necessary. Now, connect the camera to the
piggyback adapter. There should be a 1/4"‑20 mounting hole
in the bottom of the camera’s body. Thread the protruding
shaft of the piggyback adapter into the 1/4"‑20 mounting hole
in the camera a few turns. Position the camera so it is paral‑
lel with the telescope tube and turn the knurled black knob of
the piggyback adapter counter‑clockwise until the camera is
locked into position.
Aim the telescope at a deep‑sky object. It should be a fairly
large deep‑sky object, as the camera lens will likely have a
wide field of view. Check to make sure that the object is also
centered in the camera’s viewfinder. Turn the motor drive on.
Now, look into the telescope’s eyepiece and center the bright‑
est star within the field of view. Remove the eyepiece and
insert the illuminated reticle eyepiece into the focuser draw‑
tube. Turn the eyepiece’s illuminator on (dimly!). Recenter the
bright star (guide star) on the crosshairs of the reticle eye‑
piece. Check again to make sure that the object to be pho‑
tographed is still centered within the camera’s field of view.
If it is not, recenter it by repositioning the camera on the pig‑
gyback adapter, or by moving the main telescope. If you move
the main telescope, then you will need to recenter another
guide star on the illuminated eyepiece’s crosshairs. Once the
object is centered in the camera and a guide star is centered
in the reticle eyepiece, you’re ready to shoot.
Deep‑sky objects are quite faint, and typically require expo‑
sures on the order of 10 minutes. To hold the camera’s shut‑
ter open this long, you will need a lock shutter release cable.
Set the camera’s shutter to the “B” (bulb) setting. Depress the
locking shutter release cable and lock it. You are now expos‑
ing your first deep‑sky object.
While exposing through the camera lens, you will need to
monitor the accuracy of the mount’s tracking by looking
through the illuminated reticle eyepiece in the main telescope.
If the guide star drifts from its initial position, then use the
hand controller (at the 2x rate) to “move” the guide star back
to the center of the crosshairs. Any drifting along the Dec. axis
is a result of improper polar alignment, so if the guide star
drifts greatly in declination, the mount may need to be polar
aligned more accurately.
When the exposure is complete, unlock the shutter release
cable and close the camera’s shutter.
Astrophotography can be enjoyable and rewarding, as well
as frustrating and time‑consuming. Start slowly and consult
outside resources, such as books and magazines, for more
details about astrophotography. Remember ... have fun!
10. care and Maintenance
If you give your telescope reasonable care, it will last a life‑
time. Store it in a clean, dry, dust‑free place, safe from rapid
changes in temperature and humidity. Do not store the tele‑
scope outdoors, although storage in a garage or shed is OK.
Small components like eyepieces and other accessories
should be kept in a protective box or storage case. Keep the
dust cover on the front of the telescope when not in use.
Your Atlas 10 EQ requires very little mechanical maintenance.
The optical tube is steel and has a smooth painted finish that
is fairly scratch‑resistant. If a scratch does appear on the
tube, it will not harm the telescope. Smudges on the tube can
be wiped off with a soft cloth and a household cleaner such
as Windex or Formula 409.
cleaning lenses
Any quality optical lens cleaning tissue and optical lens clean‑
ing fluid specifically designed for multi‑coated optics can be
used to clean the exposed lenses of your eyepieces or find‑
er scope. Never use regular glass cleaner or cleaning fluid
designed for eyeglasses. Before cleaning with fluid and tissue,
however, blow any loose particles off the lens with a blower
bulb or compressed air. Then apply some cleaning fluid to a
tissue, never directly on the optics. Wipe the lens gently in
a circular motion, then remove any excess fluid with a fresh
lens tissue. Oily fingerprints and smudges may be removed
using this method. Use caution; rubbing too hard may scratch
the lens. On larger lenses, clean only a small area at a time,
using a fresh lens tissue on each area. Never reuse tissues.
cleaning Mirrors
You should not have to clean the telescope’s mirrors very
often; normally once every year or so. Covering the telescope
with the dust cover when it is not in use will prevent dust from
accumulating on the mirrors. Improper cleaning can scratch
mirror coatings, so the fewer times you have to clean the mir‑
rors, the better. Small specks of dust or flecks of paint have
virtually no effect on the visual performance of the telescope.