Orion 9877 - Manual (Page 11)

Confused About Pointing the Telescope?
Beginners occasionally experience some confusion about
how to point the telescope overhead or in other directions. In
Figure 1 the telescope is pointed north as it would be during
polar alignment. The counterweight shaft is oriented down-
ward. But it will not look like that when the telescope is point-
ed in other directions. Let’s say you want to view an object
that is directly overhead, at the zenith. How do you do it?
DO NOT make any adjustment to the latitude adjustment
L-bolts. That will spoil the mount’s polar alignment.
Remember, once the mount is polar aligned, the telescope
should be moved only on the R.A. and Dec. axes. To point the
scope overhead, first loosen the R.A. lock lever and rotate the
telescope on the right ascension axis until the counterweight
shaft is horizontal (parallel to the ground). Then loosen the
Dec. lock lever and rotate the telescope until it is pointing
straight overhead. The counterweight shaft is still horizontal.
Then retighten both lock levers.
What if you need to aim the telescope directly north, but at an
object that is nearer to the horizon than Polaris? You can’t do
it with the counterweights down as pictured in Figure 1. Again,
you have to rotate the scope in right ascension so that the
counterweight shaft is positioned horizontally. Then rotate the
scope in declination so it points to where you want it near the
horizon.
To point the telescope directly south, the counterweight shaft
should again be horizontal. Then you simply rotate the scope
on the declination axis until it points in the south direction.
To point the telescope to the east or west, or in other direc-
tions, you rotate the telescope on its right ascension and dec-
lination axes. Depending on the altitude of the object you want
to observe, the counterweight shaft will be oriented some-
where between vertical and horizontal.
Figure 12 illustrates how the telescope will look when pointed
at the four cardinal directions: north, south, east and west.
7. Astronomical Observing
For many users, the SkyView Pro 127mm EQ telescope will
be a major leap into the world of amateur astronomy. This
section is intended to get you ready for your voyages through
the night sky.
Observing Tips
A. Site Selection
Pick a location away from street lights and bright yard lighting.
Avoid viewing over rooftops and chimneys, as they often have
warm air currents rising from them, which distort the image
seen in the eyepiece. Similarly, you should not observe
through an open window from indoors. Better yet, choose a
site out-of-town, away from any “light pollution”. You’ll be
stunned at how many more stars you’ll see! Most importantly,
make sure that any chosen site has a clear view of a large
portion of the sky.
B. Seeing and Transparency
Atmospheric conditions play a huge part in quality of viewing.
In conditions of good “seeing”, star twinkling is minimal and
objects appear steady in the eyepiece. Seeing is best over-
head, worst at the horizon. Also, seeing generally gets better
after midnight, when much of the heat absorbed by the Earth
during the day has radiated off into space. Typically, seeing
conditions will be better at sites that have an altitude over
about 3000 feet. Altitude helps because it decreases the
amount of distortion causing atmosphere you are looking
through.
A good way to judge if the seeing is good or not is to look at
bright stars about 40° above the horizon. If the stars appear
to “twinkle”, the atmosphere is significantly distorting the
incoming light, and views at high magnifications will not
appear sharp. If the stars appear steady and do not twinkle,
seeing conditions are probably good and higher magnifica-
tions will be possible. Also, seeing conditions are typically
poor during the day. This is because the heat from the Sun
warms the air and causes turbulence.
Good “transparency” is especially important for observing
faint objects. It simply means the air is free of moisture,
smoke, and dust. All tend to scatter light, which reduces an
object’s brightness.
One good way to tell if conditions are good is by how many
stars you can see with your naked eye. If you cannot see stars
of magnitude 3.5 or dimmer then conditions are poor.
Magnitude is a measure of how bright a star is, the brighter a
star is, the lower its magnitude will be. A good star to remem-
ber for this is Megrez (mag. 3.4), which is the star in the “Big
Dipper” connecting the handle to the “dipper”. If you cannot
see Megrez, then you have fog, haze, clouds, smog, light pol-
11
Figure 12a-d. This illustration show the telescope pointed in the four cardinal directions (a) north, (b) south, (c) east, (d) west. Note that
the tripod and mount have been moved; only the telescope tube has been moved on the R.A. and Dec. axes.
a. b. c. d.