Orion SKYVIEW PRO 9829 - Manual (Page 7)

7
The polar axis finder scope is now ready to be used. When
not in use, replace the plastic protective cover to prevent the
polar finder from getting bumped, which could knock it out of
alignment.
using the Polar axis Finder scope
The reticle of the polar axis finder scope for the SkyView Pro
has a tiny star map printed on it that makes precise polar
alignment quick and easy. To align the mount using the polar
axis finder scope, follow these instructions:
1. Approximately polar-align the mount as outlined in the pre-
vious procedure.
2. Loosen the Dec. lock lever and rotate the optical tube on
the declination axis so that the tube is at a 90° to the right
ascension axis (Figure 8). Tighten the Dec. lock lever.
3. Remove the cap on the front opening of the mount (Figure
4). Focus the polar finder by rotating its eyepiece. Now,
sight Polaris in the polar axis finder scope. If you have fol-
lowed the approximate polar alignment procedure accu-
rately, Polaris will probably be within the field of view. If
not, move the tripod left-to-right, and adjust the latitude
up-and down until Polaris is somewhere within the field of
view of the polar axis finder scope.
4. Shine a red flashlight down the front end of the polar finder
to illuminate the reticle within the field of view. Make sure
the flashlight shines in at an angle, so as not to block the
polar finder’s field of view. It may be helpful to have a friend
hold the flashlight while you look through the polar finder.
Note the constellation Cassiopeia and the Big Dipper in
the reticle. They do not appear in scale, but they indicate
the general positions of Cassiopeia and the Big Dipper
relative to the north celestial pole (which is indicated by
the cross at the center of the reticle). Rotate the reticle so
the constellations depicted match their current orientation
in they sky when viewed with the naked eye. To do this,
release the R.A. lock lever and rotate the main telescope
around the R.A. axis until the reticle is oriented with sky.
For larger optical tubes, you may need to remove the tube
from the mount to prevent it from bumping into the mount.
Once the reticle is correctly oriented, use the right ascen-
sion lock lever to secure the mount’s position.
5. Now use the azimuth adjustment knobs (Figure 2) and
the latitude adjustment L-bolts (Figure 4) on the mount
to position the star Polaris inside the tiny circle marked
“Polaris” on the finder’s reticle. You must first loosen the
knob underneath the equatorial mount on the center sup-
port shaft to use the azimuth adjustment knobs. Once
Polaris is properly positioned within the reticle, you are
precisely polar aligned.
If you do not have a clear view of Polaris from your observing
site, you will not be able to use the polar-axis finder to pre-
cisely polar align the telescope.
Note: From this point on in your observing session, you
should not make any further adjustments in the azimuth
or the latitude of the mount, nor should you move the
tripod. Doing so will undo the polar alignment. The tele-
scope should be moved only about its right ascension
and declination axes.
use of the right ascension and Declination
slow‑Motion control Knobs
The right ascension (R.A.) and declination (Dec.) slow-motion
control knobs allow fine adjustment of the telescope’s position
to center objects within the field of view. Before you can use
the knobs, you must manually “slew” the mount to point the
telescope in the vicinity of the desired target. Do this by loos-
ening the R.A. and Dec. lock levers and moving the telescope
about the mount’s right ascension and declination axes. Once
the telescope is pointed close to the object to be viewed,
retighten both lock levers.
Note: If you have an optional motor drive attached you
will need to loosen the manual clutch on the R.A. (and
Dec. for dual-axis drives) gear shaft before using the
slow-motion control knob.
The object should now be visible somewhere in the tele-
scope’s finder scope. If it isn’t, use the slow-motion knobs to
scan the surrounding area of sky. When the object is visible in
the finder scope, use the slow-motion knobs to center it. Now,
look in the telescope’s eyepiece. If the finder scope is properly
aligned, the object should be visible somewhere in the field of
view. Once the object is visible in the eyepiece, use the slow-
motion knobs to center it in the field of view.
tracking celestial objects
When you observe a celestial object through the telescope,
you’ll see it drift slowly across the field of view. To keep it in
Figure 8. The optical tube must be at a 90° angle to the right
ascension axis in order to view through the polar axis finder