Cator, 35 ) to – Onkyo AVX-280 User Manual
Page 35
35
En
Note
• The
“Power Control”
setting can be set only when the above
“
HDMI Control
”
setting is set to “On”.
• HDMI power control only works with
-compatible
components that support it and may not work properly with
some components due to their settings or compatibility.
• When set to “On”, power consumption will increase.
• When set to “On”, regardless of whether the AV receiver is On
or in Standby, both audio and video stream from an HDMI input
will be output to the TV or other components via HDMI connec-
tion (HDMI pass through function). When the HDMI pass
through function activates in standby mode, HDMI THRU indi-
cator will light.
• The power consumption during standby mode will increase dur-
ing the HDMI pass through function; however if your TV sup-
ports CEC (Consumer Electronics Control), the power
consumption can be saved in the following cases:
1. The TV is in standby mode.
2. You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
■
TV Control
`
Off:
TV Control disabled.
`
On:
TV Control enabled.
Set to “On” when you want to control the AV receiver
from an
-compatible TV that is connected to
HDMI.
Note
• Do not assign the component connected with the HDMI input to
the TV/CD selector when you set “TV Control” setting to “On”.
Otherwise, appropriate CEC (Consumer Electronics Control)
operation is not guaranteed.
• Set to
“
Off
”
when the TV is not compatible or when it is unclear
whether the TV is compatible or not.
• The
“TV Control”
setting can be set only when the above
“
HDMI Control
”
and
“Power Control”
settings are both set
to “On”.
• Refer to the connected component’s instruction manual for
details.
You can change various audio settings by pressing
AUDIO.
Note
• When the “Audio TV OUT” setting is set to “On” (
➔
34),
AUDIO is disabled.
Tone Control Settings
You can adjust the bass and treble for Speakers A and B
front speakers, except when the Direct listening mode is
selected.
■
Bass
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output
by the front speakers.
■
Treble
`
–10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output
by the front speakers.
Operating on the AV receiver
Note
• To bypass the bass and treble tone circuits, select the Direct lis-
tening mode.
• This procedure can also be performed on the AV receiver by
using its TONE, –, and + buttons (
35).
Speaker Levels
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to Standby. To save the setting you made
here, go to “Level Cal (Level Calibration)” (
setting the AV receiver to Standby.
■
Subwoofer
`
–15dB to 0dB to +12dB in 1 dB steps.
■
Center
`
–12dB to 0dB to +12dB in 1 dB steps.
Note
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the “Sp Config
31) cannot be adjusted.
After changing the settings of the “HDMI Control”,
“Audio Return Ch”, “Power Control”, or “TV Con-
trol”, turn off the power to all connected pieces of
equipment and then turn them on again. Refer to the
User’s Manuals for all connected pieces of equipment.
Using the Audio Settings
1
Press
RECEIVER followed by AUDIO.
2
Use / to select an item, and
/
to change the
setting.
Repeat this step for the other settings.
1
Press
TONE on the AV receiver repeatedly to
select either “Bass” or “Treble”.
2
Use
TONE –/+ on the AV receiver to adjust.