Runco VX-4000ci - Manual (Page 23)

Rear Panel
2
Pb Pr Y
Video
3 IR
RS-232 Control
S-Video 1
S-Video 2
HD1
HD2
1 2
Pr
R
Y
G Pb
B
R
Pr
G
Y B
Pb
H V
DVI 1 DVI 2 DVI Out H/V V H
Pr
R
Y
G Pb
B
H V
TRIGGERS
RS-232 Out
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
!
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
100-230VAC 50-60 Hz, 165 Watts Max
OUTPUTS
INPUTS SYSTEM CONTROL INTERFACE
Component Video
SDI
Option
Serial No
Video Processor / Controller
Model
Runco International
Union City, CA
Made In USA
2 3 4 7 10 8 14 15 16 17
11 13
1
6 5
12 9
OUTPUTS:
1. ANALOG OUTPUTS (BNC Connectors)
The various output lines used to drive the analog
input of the display device. Individually, the jacks
are: V=vertical sync, H=horizontal sync, B=Blue,
G=Green, R=Red. Connect these to the corre-
sponding projector inputs.
NOTE: If DVI input is used with HDCP
content, RGBHV output is automatically
disabled. This is in compliance with HDCP
regulations. To switch to DVI output see
‘Projector Configuration’ on page 15.
2. DVI OUT
The DVI digital link used to drive the digital input
of an HDCP compliant display device. Connect to
the projector’s DVI inputs.
INPUTS:
3. DVI 1 (Digital)
DVI input #1, HDCP compliant.
4. DVI 2 (Digital)
DVI input #2, HDCP compliant.
5. HD 1 (Analog BNC connectors)
High Definition input #1, can be RGB(HV) or
YPrPb, 480i, 480P, 720P or 1080i.
6. HD 2 (Analog BNC connectors)
High Definition input #1, can be RGB(HV) or
YPrPb, 480i, 480P, 720P or 1080i.
7. COMPONENT INPUT (RCA connectors)
Standard Definition (480i/576i) Component
(YPrPb) input. This is the input for component
video from sources such as DVD players.
(For best
results do not run DVD player in progressive mode).
8. COMPOSITE INPUT (RCA connector)
This is the input for Composite Video input from
sources such as Laser disc players,
VCRs and other miscellaneous video sources.
9. S-VIDEO 1 INPUT
This is the input for S-video #1 from sources such
as Satellite receivers, S-VHS VCR’s and DVD
players.
10. S-VIDEO 2 INPUT
This is the input for S-video #2 from sources such
as Satellite receivers, S-VHS VCR’s and DVD
players.
11. TRIGGERS 1/2/3 (Outputs)
Connection for 3 different 12V trigger controlled
devices.
12. RS-232 OUT (RJ-11 Connector)
Comlink connection to VX-4000ci projector.
13. IR
Wired input from an external remote control.
14. RS-232 CONTROL
Connection for an external RS-232 controller
device to place the DHD under system automation
control.
15. POWER INPUT (100-230v)
Plug in main power here.
16. MAINS FUSE
This is the main AC input fuse. (Main Fuse:
5mm x 20mm, 500mA, 250V, Slow Blow)
17. MAIN POWER SWITCH
Disconnects or applies main power to the
processor.