Roland VC-200HD - Manual (Page 35)

35
Menus and settings
200–275 Processing Parameter (continued)
* The values enclosed in a [box] are the factory defaults.
300–391 Output Parameter
* The values enclosed in a [box] are the factory defaults.
* For items 350 and 351, please adjust while confirming on a monitor speaker.
Item
Number Item Name Description and Available Settings
274 User Bit Sets the user bit embedded in the timecode when "Free Run" is set with "270: TC Generate."
* Because there is no impact when the value set for "270: TC Generate" is not "Free Run," the input user bit is
passed through without any change. If no user bit is input, "FF FF FF FF" is output.
This item sets each value independently.
[00]–FF, [00]- FF, [00]–FF, [00]- FF: May be adjusted in this range.
275 Drop Frame Selects drop frame/non-drop frame for the time code when "Free Run" is set with "270: TC Generate."
[Drop]: Selects Drop Frame.
Non Drop: Selects Non-drop Frame.
* The setting is not valid when "1080/50p," "1080/50i," "720/50p," "576/50p," or "576/50i" is selected with
"300: Video Out Format."
Item
Number Item Name Description and Available Settings
300 Video Out Format Selects the format of the video to output. [Auto]: One of the following formats is automatically selected,
so as to match the format of the input video.
1080/59.94p, 1080/50p, 1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 480/59.94p, 576/50p, 480/59.94i,
576/50i: Select one of these formats.
* If "Auto" is set or if "Free Run" is set with "270: TC Generate" of the video input being used, the time code count
is reset when this item setting is changed
311 Out 480i Setup Sets the video output setup level of the COMPONENT OUT connector when 480/59.94i is selected for
“300: Video Out Format.”
[0IRE]: Selects 0IRE. (NTSC Japan/PAL)
7.5IRE: Selects 7.5IRE. (NTSC excluding Japan)
320 Audio Out Fs Sets the sampling frequency of the digital audio output from the i.LINK connector or HD-SDI OUT con-
nector.
[48 kHz]: Outputs audio in 48 kHz.
32 kHz: Outputs audio in 32 kHz. If "480/59.94i" or "576/50i" is selected with "300: Video Out Format" at
this time, the output from the i.LINK connector is a DV signal and the audio is 4 channel. If anything else
is set, no video is output from the i.LINK connector.
330 AudioOutCh1&2Lv Sets the audio output level for AUDIO OUTPUT connectors CH1 and CH2.
Mute: Mutes the audio.
-40 dB –[0]– +12 dB: Adjusts the sound output level.
331 AudioOutCh1&2Lv Sets the audio output level for AUDIO OUTPUT connectors CH3 and CH4.
Mute: Mutes the audio.
-40 dB –[0]– +12 dB: Adjusts the sound output level.
340 Audio Out Mode Sets the audio mode of the audio output from the AUDIO OUT connector
[2Ch]: Outputs 2 channels.
4Ch: Outputs 4 channels.
350 Out Ch1&2 NomLv Sets the output Nominal level for AUDIO OUTPUT connectors CH1 and CH2.
[+4dBu], -2dBu, -4dBu, -10dBu: Larger numerical values indicate higher levels.
351 Out Ch3&4 NomLv Sets the output Nominal level for AUDIO OUTPUT connectors CH3 and CH4.
[+0dBu], -6dBu, -8dBu, -14dBu: Larger numerical values indicate higher levels.
360 DV Locked Audio When outputting with the DV format from the i.LINK connector, sound is output with “Locked Audio.”
[Off]: Do not use locked audio.
On: Use locked audio.