ROTEL RCD-06 - Manual (Page 8)

8
REVIEW Button I
Remote Only
This button is used to review the memorized
tracks in PROGRAM mode. Press the button
and the first memorized track number will
appear in order in the Display, flashing for
approximately five seconds. Pressing the
REVIEW button again while the track number
is flashing will continue the review sequence,
showing the next memorized track. Continue
pressing the REVIEW button to see the complete
memorized track list.
If you do not press the REVIEW button while
the track number is flashing, the review process
is terminated and the unit resumes whatever
mode it was in before you started to review,
except that the last reviewed track number will
remain active and shown in the display.
Note that you may remove a selection from the
play list during the review procedure using the
CLEAR button, as described below.
CLEAR Button H
Remote Only
This button allows you to remove a track se-
lection from the memorized program play list
during the review procedure described above.
Follow the review procedure until the desired
track number is flashing. Then, instead of press-
ing the REVIEW button to continue, remove the
displayed track by pressing the CLEAR button
while the number is still flashing. You may then
continue the review procedure.
RANDOM Button D
Remote Only
This instructs the CD player to play tracks from
the entire disc in random order. Once all of
the selections have been played once, the disc
will stop playing, unless the REPEAT Button
(see below) has been engaged, in which case
the random play will continue until the STOP
button is pressed. When the RANDOM button
is engaged, the word RANDOM appears in
the Display.
REPEAT Button C
Remote Only
This button allows you to repeat the current
track or the entire disc continuously until the
feature is cancelled by disengaging the REPEAT
button or pressing STOP. The REPEAT button
steps sequentially through the available op-
tions. Press the button once and the RCD-06
will repeat just the current track, displaying
the indicator REPEAT 1 in the Display. Press
the button a second time and the RCD-06 will
repeat the entire disc, displaying REPEAT ALL
in the Display. Press the button a third time to
cancel the REPEAT function.
As noted above, REPEAT can be used in con-
junction with the RANDOM play feature.
NOTE: The REPEAT function is automatical-
ly cancelled when the disc drawer is
opened.
SCAN Button E
Remote Only
This feature automatically plays the first ten sec-
onds of each track on the disc (or the memorized
program). To activate the feature, press the
SCAN button. The word INTRO appears in the
Display. To stop scanning and resume normal
operation at the current track, press the SCAN
button again or press the PLAY button.
TIME Button G
Remote Only
Normally, the RCD-06 displays the elapsed time
of the currently playing track. The TIME button
allows you to step through two alternative time
displays. Pressing the button once displays
the time remaining in the current track, which
counts down as the track continues playing.
Pressing the button a second time displays the
time remaining on the entire disc (or memorized
program). Pressing the button a third time
reverts to the standard elapsed time display.
When the TIME feature is activated, the word
REMAIN appears in the Display.
External Remote Input
w
This 3.5 mm mini-jack (labeled EXT REM IN)
receives command codes from an industry-
standard infrared receiver (Xantech, etc.)
located in the main listening room. This feature
is useful when the unit is installed in a cabinet
and the front-panel sensor is blocked. Consult
your authorized Rotel dealer for information
on external receivers and the proper wiring of
a jack to fit the mini-jack receptacle.
12V Trigger Connection
q
The RCD-06 can be activated by a 12 volt
trigger signal from a Rotel preamplifier.
The trigger input accepts any control signal (AC
or DC) ranging from 3 volts to 30 volts. When
a cable is connected to the input and a trigger
signal is present, the CD Player is activated.
When the trigger signal is interrupted, the
unit goes into standby mode. The front panel
indicator light remains lit, but the display goes
dark and the unit will not operate.
NOTE: When using the 12V Trigger feature,
leave the POWER button in the ON position.
RCD-06 Stereo Compact Disc Player