NEC R 37 Xtra User Manual
Page 18
18
26
25
External Speaker Connections
External speakers may be connected to the monitor to reproduce sound from
VIDEO 1, VIDEO 2, RGB 1 or RGB 2 signal sources.
External speakers may be connected directly to the EXTERNAL SPEAKERS
terminals or indirectly by connecting a stereo system amplifier to the audio
outputs.
WARNING: Speakers that are installed next to the monitor must be
shielded against electromagnetic radiation which can cause color distortion
in the CRT and is not covered under the warranty.
If non-shielded speakers are used, they must be located a minimum of 4 feet
away from the monitor.
CAUTION: Unplug the monitor and all connected components before con-
necting external speakers. Use only speakers with 8-ohm impedance and a
power output rating of 5 watts or more.
79644641
POWER
ON
RGB 2
RGB 1
VIDEO 2
VIDEO 1
POSITION / CONTROL
PROCEED
EXIT
SCAN
NORMAL
SIDE PIN
HEIGHT
WIDTH
BRIGHT CONTRAST MUTE
NORMAL
VOLUME
OFF
DEGAUSS
MULTIMEDIA MONITOR
RD-346E
VIDEO 1
VIDEO 2
RGB AUDIO
RGB 1
REMOTE EXTERNAL CONTROL
DIP SW
AC IN
SPEAKER SELECT
EXT SPEAKER
RGB 2
AUDIO
AUDIO
HIGH
75
Ω
R
MONO
IN
THROUGH
OUT
IN
THROUGH
OUT
THROUGH
OUT
IN
BNC
S
HIGH
75
Ω
THROUGH
OUT
IN
R
THROUGH
OUT
IN
R
THROUGH
OUT
IN
BNC
S
HIGH
75
Ω
IN
THROUGH
OUT
R/CR/PR
G/Y/Y
B/VB/PB
H/CS
V
HIGH
75
Ω
HIGH
75
Ω
SPEAKRES MUST
HAVE MORE THAN
5WATT RATING
INPEDANCE 8 OHM
RIGHT
LEFT
INT
EXT
IN
THROUGH
OUT
1 2 3 4 5 6 7 8
ON
(
)
L
MONO
(
)
L
MONO
(
)
L
MONO
(
)
L
SPEAKER SELECT
INT
EXT
RIGHT
4 ft.
120cm
4 ft.
120cm
Left
Right
To connect the monitor to stereo system speakers:
1. Connect L AUDIO output to the stereo amplifier L AUX input.
2. Connect R AUDIO output to the stereo amplifier R AUX input.
3. Set SPEAKER SELECT switch at EXT to use external speakers only. For
center channel audio fill, set SPEAKER SELECT at INT for sound from both
monitor and external speakers.
IMPORTANT: Do not connect speakers to both the monitor EXTERNAL
SPEAKERS terminals and to the stereo amplifier. This could damage both
the monitor and the speakers.
VIDEO or
RGB AUDIO L and R outputs of XP37Xtra/XM37Xtra
To connect external speakers directly to the monitor:
1. Strip the ends of the speaker wires.
2. Press down a button below the EXTERNAL SPEAKERS terminals, insert
the speaker wire and release the button to secure a speaker wire connec-
tion:
[a] Connect the right speaker (located at right side of the monitor when
viewed from the front) positive (+) wire to RIGHT +.
[b] Connect the right speaker negative (-) wire to RIGHT -.
[c] Connect the left speaker negative (-) wire to LEFT -.
[d ]Connect the left speaker positive wire (+) to LEFT +.
3. Set SPEAKER SELECT switch at EXT.
HJJKKKASDFFF
BNGGDFDFGHY
ZZXXC
CCVDFVFF
ADFGRTRYT
ADFGRTRYT
SFGHHHJJ
SFGHHHJJ
DFFGGGG
AFHUJTT
AFHUJTT
DFFGGGG
2Q
2Q
2Q
2Q
JGHDYSTEOYII DYASGHIROYUKIAIZAWA
THROUGH
OUT
IN
R
R
L
LINE OR
AUX INPUT
LINE OR
AUX INPUT
STEREO AMP
L (MONO)
NOTE: The speaker cables must be less than 3m in length.