Rear panel identification of controls – NAD L70 User Manual

Page 8

ATTENTION!

Please make all connections to your L70 receiver with the unit unplugged. (It is also advisable to power-down or unplug all associated components
while making or breaking any signal or AC power connections.)

ANTENNA

CAB/SAT

INPUT

VCR

MONITOR

AUDIO

S-VIDEO

GND

OUT

DIGIT

DIGITAL

AL OUTPUT

OUTPUT

COMPONENT

VIDEO OUT

VIDEO

CENTER

FRONT

SURROUND

5.1 CHANNEL INPUT

CENTER

SURROUND

OSD SELECT

FRONT

SUBW

VIDEO

S-VIDEO

SPEAKERS

AC OUTLET

SWITCHED

DIGITAL AUDIO

INPUT

COAXIAL

OPTICAL

OUTPUT

SUB

WOOFER
PRE-OUT

12 V TRIGGER

OUT

INPUT

SCAR

SCART/RGB OUT

T/RGB OUT

240 VOLT EUROPEAN
VERSION ONLY

120 VOLT
NORTH AMERICAN
VERSION ONLY

POWER

AC OUTLET

SWITCHED

100WATTS MAX

REAR PANEL

Identification of controls

ENGLISH

FRANÇAIS

DEUTSCH

NEDERLANDS

ESP

AÑOL

IT
ALIANO

POR

TUGUÊS

SVENSKA

SWITCHED AC OUTLET: This convenience jack can supply switched

power to another component or accessory. It is powered on and off
by the front panel POWER key (or the HTR L70’s ON and OFF keys).

NOTE

The total draw of all devices connected to this jack must not exceed
100 watts.

2 AC POWER CORD: Connect AC power cord to the Voltage

according to the model, 120 V for US and 240 V for Euro models.

3 MONITOR OUT: Connect to video input of the monitor/television,

using quality dual-RCA and/or S-Video cables designed for video
signals. In general, the S-Video connection is superior and should be
used if your TV/monitor provides the corresponding input.

4 OSD SELECTOR: This switch places the OSD (On Screen Display) to

either the Composite or S-Video MONITOR OUT.

5 COMPONENT VIDEO OUT (NTSC only): Connect the L70

COMPONENT VIDEO OUT to the component-video input of a
compatible video monitor/TV. Be sure to observe consistency in
connecting the Y/Cr/Cb jacks (some source and TV components label
these Y/Pb/Pr) to the corresponding sources/inputs; do not rely purely
on the colour coding of the jacks, which may not always be
consistent among brands. The routing of the component-video input
is fixed: COMPONENT VIDEO OUT jack will only display the internal
DVD video signals.

NOTE

The L70’s component-video output is a fully wide-band output,
compatible with all HDTV formats. The L70 does not display its on-
screen menus on its component-video output. To use on-screen
menus, you will need to make an S-Video or composite connection
between the L70 and the monitor/TV, and select it for menu display.
Refer to OSD SELECTOR.

6 FM ANTENNA: The supplied wire “dipole” FM antenna will connect

to the FM connector using the supplied “balun” adaptor. It will
usually work best when mounted on a vertical surface such as a wall,
with arms fully outstretched forming a horizontal “T” perpendicular
to the origin point of the signal. Experiment with placement and
orientation of to yield the clearest sound and lowest background
noise. In areas of difficult FM reception an external FM antenna can
yield dramatic gains in quality; consult your NAD audio specialist or
a professional antenna installer.

7 AM ANTENNA: The AM loop antenna supplied with the L70 (or a

suitable replacement) is required for AM reception. Open the clip
terminal lever; insert the wire and close, ensuring that the lever locks
the wire in place. Testing different positions for the antenna may
improve reception; vertical orientation will usually produce the best
results. Antenna proximity to large metal objects (appliances;
radiators) may impair reception, as will attempts to lengthen the wire
to the loop.

NOTE

An external AM antenna can improve long-distance reception
substantially; consult your NAD audio specialist or a professional
antenna installer. Do not connect anything other than a loop antenna
to the AM ANTENNA terminal. Do not remove the AM loop antenna.

240 volt
European
version only

120 volt North
American
version only

240 volt European
version only

120 volt North American
version only