Nilfisk-Advance America P 130.2 - Manual (Page 4)

4
Nilfisk P 130.2 / P 150.2 / P 160.2
EN adversely affect the safety of
the appliance.
 Disconnect from electrical
power supply before carrying
out user maintenance.
 To ensure the appliance
safety only use original spare
parts from the manufacturer
or approved by the manufac-
turer.
 High pressure hoses, fi ttings
and couplings are important
for the safety of the appli-
ance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.
 Do not use the appliance
if a supply cord or impor-
tant parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trig-
ger gun.
 The appliance is intended for
cleaning outdoors.
 Appropriate ear protection
must be used.
 Never use the machine in
an environment where there
could be a danger of explo-
sion. If any doubt arises,
please contact the local
authorities.
 It is not allowed to clean
asbestos- containing surfaces
with high pressure.
 This high pressure washer
must not be used at tempera-
tures below 0°C.
 Never let any persons stay
under the product when
stored on the wall.
WARNING!
Inadequate extension cables
can be dangerous. Cables on
reels should always be com-
pletely unwound to prevent the
cable from overheating.
Extension cables should be of
a watertight construction and
comply with the below-men-
tioned requirements for length
and cable dimensions.
1.0 mm² max. 12.5 m
1.5 mm² max. 20 m
2.5 mm² max. 30 m
 If the electric cable is
damaged, it must be re-
placed by the manufacturer
or his service agent or simi-
larly qualifi ed person in order
to avoid a hazard.
Mains power connection
The following should be ob-
served when connecting the
high pressure washer to the
electric installation:
 Only connect the machine to
an installation with earth con-
nection.
 The electric installation shall
be made by a certifi ed elec-
trician.
 It is strongly recommended
that the electric supply to this
machine should include a re-
sidual current device (GFCI).
Water connection
Connection to the public mains
according to regulations.
This high pres-
sure washer is
only allowed to be
connected with
the drinking water
mains, when an appropriate
backfl ow preventer has been
installed, Type BA according
to EN 1717. The backfl ow pre-
venter can be ordered under
number 106411177. The length
of the hose between the back-
fl ow preventer and the high
pressure washer must be at
least 10 metres to absorb pos-
sible pressure peaks (min diam-
eter ½ inch).
Operation by suction (for ex-
ample from a rainwater vessel)
is carried out without backfl ow
preventer. Recommended suc-
tion set: 126411387.
As soon as water has fl own
through the BA valve, this water
is not considered to be drinking
water any more.
IMPORTANT! Only use wa-
ter without any impurities. If
there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi-
tional fi lter should be mounted.
Repair and maintenance
WARNING! Always remove the
electric plug from the socket be-
fore carrying out maintenance
work on the machine.
Safety devices
Locking device on spray handle
(7a) (see illustration at the end
of this manual):
The spray handle features a
locking device. When the button
is activated, the spray handle
cannot be ope rated.
Thermal sensor:
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen-
sor has cooled.
Pressure safety device
An integrated hydraulic safety
valve protects the system from
excessive pressure.