NAD L 53 - Manual (Page 8)

8
ENGLISH
FRANÇAIS
DEUTSCH
NEDERLANDS
ESP
AÑOL
IT
ALIANO
POR
TUGUÊS
SVENSKA
FRONT PANEL
Identification of controls
©
N AD
2004
L53 DIGITAL CHAPTER
TRACK
DVD Receiver L 5 3
FM MUTE/ MODE SETUP/ MEMORY TIMER ON/OFF AUDIO MODE PLAY/ PAUSE INPUT SELECT STOP/ OPEN
S-VIDEO
PHONES VIDEO 4 INPUT
L R (MONO)
AUDIO
VIDEO
SCAN/TUNE SKIP/PRESET
VOLUME (SETUP) DISPLAY
DELETE
L R
LFE
1 & 2
16 14 15 18 17
5 7 12 13 8 3 6 4 9 10 11
1 “Power”: When the L53 is first plugged into the AC power, the L53’s
clock will light in the main VFL display showing the time of day. Press
in to switch the receiver from standby, changing the standby
indicator from bright blue to dark, and illuminating the VFL display.
Pressing the power switch again turns the unit back to standby. It is
usual (and perfectly acceptable) to leave the L53 in standby mode in
between normal viewing and listening sessions. Pressing the “OPEN
CLOSE” button on the front-panel, or the HTR L53 remote’s “ON”
button, will switch the receiver on, making it operational. Press the
remote’s “OFF” button to return to standby. Note that when you do
choose to switch off to standby using the front panel Power button,
the L53’s memory back-up system will store channel level, tuner
preset, and other settings for several weeks while the unit is switched
off, or even unplugged from AC power altogether.
2 INDICATOR: When the L53 is in standby the LED will light bright
blue, the VFL in the L53 will display the L53’s internal clock. This
indicator will extinguish itself when the power cable is unplugged
from the AC supply.
3 REMOTE SENSOR: Point the remote control at the remote sensor
and press the buttons. Do not expose the remote sensor of the
receiver to a strong light source such as direct sunlight or
illumination. If you do so, you may not be able to operate the
receiver with the remote control.
Distance: About 23 ft (7 m) from the front of the remote sensor
Angle: About 30° in each direction of the front of the remote sensor
4 TIMER ON/OFF: Press and hold to set the internal clock, ON/OFF
timer, and display of the clock’s time. A red “clock face” will appear
in the fluorescent display when the timer is activated. To set the
internal clock, press and hold the “TIMER ON/OFF” button for more
than 4 seconds. Use the “MEMORY” button to toggle between the
hours and minutes. Use the “SKIP/PRESET” buttons to change the
hours and minutes. There are two timers, one for when the L53
powers on, the other for when the unit powers off; these too are
programmed in the same way.
5 FM MUTE/MODE: In the normal Mute position, only the stations
with a strong signal can be listened to, and the noise between
stations is muted. Pressing the “FM MUTE/MODE” button allows
distant (and potentially noisy) stations to be received. (See “Listening
to Radio”.
6 SETUP/MEMORY: Use to store tuned stations to the L53’s 60
preset-memory locations. (See “Listening to Radio”)
When DVD is selected, use this button for setting the DVD-player’s
options as shown on the On Screen Display (OSD). (See “Using the
L53’s DVD/VCD/CD player”)
7 DISPLAY: Use this multifunction button to toggle between RDS PS,
RDS RT and station frequency in FM Tuner mode (see “Listening to
Radio”). When in ether CABLE\SAT or VCR mode, this "DISPLAY"
button will toggle between Optical or Coaxial and analog inputs.
You can assign either Optical or Analog input to VCR, and either
Coaxial or Analog input to CABLE/SAT. When in DVD mode,
pressing "DISPLAY" will toggle between the two DVD navigation
menus as well.
L53 IM english v3.qxd 7/20/2005 3:04 PM Page 8