Central station receiver 1 format, Enter user codes, Through – Napco Security Technologies GEM-P1632 User Manual
Page 11: For a zero and, For a blank space (•). press, For letters b–e, respectively. press, User # user code option level access control
11
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number
buttons
1
through
9
. NOTE: Press
G0
for a zero and
0
for a blank space (•). Press
G 1
through
G 4
for letters B–E,
respectively. Press
J
to save. Press NEXT (
E
) button to proceed.
NOTE: Central Station Receiver 2 and 3 Formats can only be entered in Direct
Address Programming. See CS Receiver Options.
Enter User Codes
For default program, enter up to 8 User Codes for Area 1 (Users 1 - 8) and up
to 8 User Codes for Area 2 (Users 9 - 16) . Press the (
A
) button once to
set the cursor to the User Number.
1 Enter the User Number to be programmed, including leading zeros. Use the number buttons
0
through
9 .
2 Enter a User Code of up to 6 digits. Use the number buttons
0
through
9
to enter the code followed by
G0
for each blank.
3 Enter the User Options. Refer to the User Option table below.
4 Enter the Authority Level. Refer to the Authority Level table below.
5 If this code is to be used to activate a door strike, assign the User to the appropriate access control keypad from the
Access Control Keypad table below.
Programming the GEM-P3200 & GEM-P9600
(Direct Entry)
05
INTERIOR
BYPASS
FIRE/TBL
SYS TBL
CHIME
INTERIOR
BYPASS
SYS TBL
CHIME
FIRE/TBL
(
Direct Entry)
06
INTERIOR
BYPASS
FIRE/TBL
SYS TBL
CHIME
INTERIOR
BYPASS
SYS TBL
CHIME
FIRE/TBL
DATA
ENTRIES
AUTHORITY
LEVEL
COD E
TYPE
blank (•)
NONE
ARM/DISARM
1
LEVEL 1
ARM/DISARM
2
LEVEL 2
ARM/DISARM
3
LEVEL 3
ARM/DISARM
4
NONE
ARM ONLY
5
LEVEL 1
ARM ONLY
6
LEVEL 2
ARM ONLY
7
LEVEL 3
ARM ONLY
8
NONE
SERVICE
9
LEVEL 1
SERVICE
0
LEVEL 2
SERVICE
B
LEVEL 3
SERVICE
USER OPTIONS
DATA
ENTRIES
BLOCKED
VIEW
USER
PROGRAM
BYPASS
OVERVIEW
blank (•)
DISABLED
1
Y
2
Y
3
Y
Y
4
Y
5
Y
Y
6
Y
Y
7
Y
Y
Y
8
Y
9
Y
Y
0
Y
Y
B
Y
Y
Y
C
Y
Y
D
Y
Y
Y
E
Y
Y
Y
F
Y
Y
Y
Y
ACCESS CONTROL KEYPADS
DATA
ENTRIES
K.P. 5
K.P. 6
K.P. 7
blank (•)
NONE
1
Y
2
Y
3
Y
Y
4
Y
5
Y
Y
6
Y
Y
7
Y
Y
Y
ACCESS CONTROL KEYPADS
DATA
ENTRIES
K.P. 1
K.P. 2
K.P. 3
K.P. 4
blank (•)
NONE
1
Y
2
Y
3
Y
Y
4
Y
5
Y
Y
6
Y
Y
7
Y
Y
Y
8
Y
9
Y
Y
0
Y
Y
B
Y
Y
Y
C
Y
Y
D
Y
Y
Y
E
Y
Y
Y
F
Y
Y
Y
Y
User # User Code
Option Level
Access Control
When programming User Options, Authority Level and Access Keypads:
“A” =
G 0 ; “B” = G 1 ; “C” = G 2 ;
“D” =
G 3 ; “E” = G 4 ; “F” = G 5 .
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
and press
J
to save. Similarly, to cancel a code, blank out each number of the code press
J
to save.
DATA
ENTRY
CS RECEIVER 1 FORMAT
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
8
Radionics BFSK
9
FBI 4/3/1
DATA
ENTRY
CS RECEIVER 1 FORMAT
0
Radionics Modem 2
B
SIA
C
Ademco Point ID
D
Ademco Expres
E
Pager
DATA
ENTRY
CS RECEIVER 1 FORMAT
•(blank)
Ademco Slow, Silent Knight Slow
1
Sescoa, Vertex, DCI, Franklin Fast
2
Radionics Fast
3
Silent Knight Fast