Pioneer VSX-1016V-K - Manual (Page 44)

Other connections 09
44
En
Chapter 9:
Other connections
Caution
• Make sure the power is switched off before making or
changing the connections.
Connecting using HDMI
If you have a HDMI or DVI (with HDCP) equipped compo-
nent, you can connect it to this receiver using a commer-
cially available HDMI cable.
The HDMI connection transfers uncompressed digital
video, as well as almost every kind of digital audio that the
connected component is compatible with, including
DVD-Video, DVD-Audio (see below for limitations), Video
CD/Super VCD, CD and MP3.
1 Use an HDMI cable to connect the HDMI IN 1/2
interconnect on this receiver to an HDMI output on your
HDMI component.
HDMI appears on the front panel when an HDMI-
equipped component is connected.
2 Use an HDMI cable to connect the HDMI OUT
interconnect on this receiver to an HDMI interconnect
on a HDMI-compatible monitor.
• The arrow on the cable connector body should be
facing right for correct alignment with the connector
on the player.
3 To hear audio from your HDMI component through
this system, make analog and/or digital connections as
necessary.
On the rear panel, you must connect to the audio jacks
from a set of audio/video inputs (for example,
DVR/VCR1
or DVR/VCR2 as shown in the illustration).
• Without this connection, HDMI audio will still be
output from your TV or plasma display (though no
sound will be heard from this receiver).
4 Assign the HDMI input(s) you connected to the
corresponding input source.
After connecting, you must specify which inputs(s) you
are using for your HDMI component in
Assigning the
HDMI inputs on page 50.
5 Use the input source buttons to select the input
source you assigned in the previous step, then press
SIGNAL SEL to select the audio input signal.
You can also use the front panel controls to do this (see
Choosing the input signal on page 29).
• If the video signal does not appear on your TV or
plasma display, try adjusting the resolution settings
on your component or display. Note that some
components (such as video game units) have
resolutions that may not be displayed. In this case,
use an (analog) S-video or composite connection.
About HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD players, DTV, set-top boxes, and other AV
devices. HDMI was developed to provide the technolo-
gies of High Bandwidth Digital Content Protection
(HDCP) as well as Digital Visual Interface (DVI) in one
specification. HDCP is used to protect digital content
transmitted and received by DVI-compliant displays.
CD
IN IN IN IN IN OUT OUT OUT
IN IN IN OUT OUT
CD-R/TAPE/MD DVD/LD DVR/VCR1 DVR/ TV/SAT
CONTROL
AUDIO
ANTENNA
AM L
Y P B P R Y P B P R
Y P B P R Y P B P R
DIGITAL
ASSIGNABLE
OPTICAL
COAXIAL
VIDEO
S-VIDEO
COMPONENT VIDEO
OUT
HDMI
ASSIG-
NABLE
OUT
(TV/SAT)
(CD)
(DVR/
VCR1)
IN
IN 1
IN 2
OUT
1
IN
1
IN
2
IN
3
(DVD/LD) IN 1
(DVR/VCR2)
IN 2
IN 2
IN 3
3 1
R
L
R
L
OUT
IN
2 1
ASSIGNABLE 3 1
HDMI OUT
HDMI IN
HDMI/DVI-equipped component
HDMI/DVI-compatible monitor
or plasma display
VSX-1016V
DIGITAL OUT AUDIO OUT
AUDIO R L
VSX-1016_HY.book.fm 44 ページ ２００６年２月２４日 金曜日 午前１１時５３分