Pioneer PWM-T210 User Manual

Page 3

PWM-T210

Installation Instructions

Page 3

Safety Precautions

This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation specialists or your dealer should
install the mount and set up the plasma display in order to avoid personal injury or property damage. Premier does not assume liability for injury or damage,
including liability, caused by improper installation, mounting or setup of the plasma display, misuse, modification or natural disasters.

The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation.
The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an
easily accessible location for future reference.

The wall being considered for mounting must be capable of supporting at least five (5) times the weight of 40Kg. If it is not, the wall must be reinforced before
beginning installation.

Only use specified parts for the installation of the mounting bracket. Do not use the mounting hardware from any other mount or any other source.

Handling by other than professional contractors is prohibited.

Indicates that the power plug is to be disconnected from the power outlet.

Disassembly of the plasma display is prohibited.

Safety precautions must be taken at all times.

Warning and caution in general.

Contact Premier Mounts for any technical/installation questions.

Warning Statements

The wall or ceiling structure must be capable of supporting at least five (5) times the weight of the plasma display. If not, the wall or ceiling must be reinforced.
Proper installation procedure by qualified personnel as outlined in the installations instructions must be followed. Failure to do so could result in serious personal
injury.

Installation Location

A secured structure wooden stud wall must always support the weight or load
of the plasma display. Always confirm the center of the wood stud before
beginning the installation. Failure to do so could result in personal injury and
physical damage.

Avoid installing the plasma display in locations where temperatures and
humidity are excessively high, or contact with any water or vapors possible.
This could result in fire, electrical shock and damage to the plasma display.
Water will damage the wall structure for wall mount installation.
The permissible temperature is (0-40ºC) and humidity is (20%-80%).

The mount is designed to be used on vertical walls only. Do not install near or
on doors, angled ceilings, walls, or any other installations other than wall
mounting. Failure to do so could result in damage and injury. This wall mount
is to be used only with a Pioneer plasma display. Use with any
plasma display other than Pioneer is prohibited and may cause injury and dam-
age.

Make sure the plasma display mounting area is completely free of
internal or external wires, pipes, gas lines, phone lines, etc. Failure to do
so may result in injury and damage to the walls, wiring or piping system.

Do not block the ventilation holes. Sufficient clearance must be left in the
area surrounding the plasma display and wall mount to avoid blocking
the vents and causing the plasma display to overheat which could cause
a risk of fire. Leave 100mm or more away from all of the
surrounding four sides for proper airflow.

Do not install in locations where there is vibration, movement or danger
of impact. Failure to do so could result in plasma display cracking or
falling from the wall causing damage and injury.
Do not install near heater, fireplace, direct sunlight or air conditioning or
any other source of direct heat energy. Failure to do so may result in
damage to the plasma display and could cause a risk of fire.
It is not necessarily to open the plasma display prior to installation. Never
open the plasma display or modify the mount. This mount is to be used
only as outlined in the installation instruction. Failure to do so may result
in damage and injury. If a malfunction or problem occurs with the plas-
ma display display, contact the nearest dealer or Pioneer.

Avoid Installations where there is danger of contact with over excessive dust,
oil smoke, and tobacco smoke. Failure to do so may result in fire or damage
to the plasma display or its internals.

At least two qualified people should always perform the installation work.
Injury and damage can result from dropping or bending the plasma display.

All four (4) Lag bolts must be properly secured to the wall studs. The lag bolts
must always be secured through the center of the wood studs. Failure to do so
could result in the plasma display falling from the wall causing damage to the
plasma display and personal injury.

All bolts must be properly tightened and secured before installing the
plasma display. Failure to do so could result in the plasma display falling
causing damage to the plasma display and personal injury.

Objects on the wall may collect dust quicker than anticipated. Check
periodically for dust accumulation. Refer to the plasma display installa-
tion instructions for cleaning instructions.

All hardware must be firmly tightened and secured to the plasma display in
the correct locations. If the hardware is not properly installed, do not hang the
plasma display to the wall mount. Damage and injury could result from the
plasma display falling down.

Do not play around the plasma display or throw any objects near or at
the screen. The screen is very sensitive and may scratch or break or
cause the plasma display to fall from the wall causing personal injury
and damage.

Safety Precautions