beautypg.com

Warning, For your safety: read before lighting, Minimax ch millivolt lighting/operation – Pentair MiniMax CH User Manual

Page 5: Lighting instructions to turn off gas to heater

background image

Rev. C 1-22-04

P/N 472128

5

Operation (contd.)

FOR YOUR SAFETY: READ BEFORE LIGHTING

A. This heater is equipped with a pilot which must be

lighted manually. When lighting the pilot, follow

these instructions exactly.

B. BEFORE LIGHTING smell all around the heater

area for gas. Be sure to smell next to the floor

because some gas is heavier than air and will settle
on the floor.

WHAT TO DO IF YOU SMELL GAS
-

Do not try to light any heater.

-

Do not touch any electrical switch; do not use any

phone in your building.

-

Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

-

If you cannot reach your gas supplier, call the Fire

Department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don't try to repair it. Call a qualified

service technician. Forced or attempted repair may

result in a fire or explosion.

D. Do not use this heater if any part has been under

water. Immediately call a qualified service

technician to inspect the heater and to replace any

part of the control system and any gas control which

has been under water.

MINIMAX CH MILLIVOLT LIGHTING/OPERATION-

NATURAL GAS & PROPANE

1. STOP! Read the safety information above.
2. Set the thermostat to the lowest setting.
3. Turn off electric power to the heater.
4. Push in gas control knob slightly and turn clock-

wise

to “OFF”.

Gas control knobs shown in “OFF” position.

NOTE

Knob cannot be turned from “Pilot to “OFF”” unless
knob is pushed in slightly. DO NOT FORCE.

5. Wait five (5) minutes to clear out any gas. If you then

smell gas, STOP! Follow "B" in the safety informa-

tion above. If you don't smell gas, go to the next step.

6. Push in gas control knob slightly and turn counter-

clockwise to “Pilot”.

If you do not follow these instructions exactly, a fire or explosion may result causing personal injury, loss of life

and property damage.
Since propane gas is heavier than air, escaping propane will accumulate and remain at ground level. Do not

attempt to light the heater. If you suspect a propane leak, lighting the heater can result in a fire or explosion

which can cause personal injury, death, and property damage.

WARNING

7. Push the control knob all the way and hold in.

Immediately light the pilot with Presslite matchless
ignition system by pressing the red igniter button
(located at the panel next to the gas valve). Continue
to hold the control knob in for about one (1) minute
after the pilot is lit. Release knob and it will pop
back up. Pilot should remain lit. If it goes out, repeat
steps 4 through 7.

If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.

If the pilot will not stay lit
after several tries, turn the
gas control knob to “OFF”
and call your service
technician or gas supplier.

8. Turn knob on gas control

counterclockwise to
“ON”.

9. Replace the control access

door.

10. Set the thermostat to the

desired setting.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO HEATER

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the heater if service is

to be performed.

3. Remove control access door.

4. Push in gas control knob slightly and turn clockwise

to "OFF". Do not force.

5. Replace control access door.

Robertshaw Millivolt Gas Valve

Honeywell Millivolt Gas Valve

Figure 1.

Figure 2.

Figure 3.

Figure 4.

Pilot