beautypg.com

Connect wires: iso connectors 1, Mount in the dashboard, Turn on 1 – Philips CED750 User Manual

Page 2: Set clock 1, Tune to a radio station 1, Play discs 1, Insert usb or sd/mmc card 1, Pair the bluetooth-enabled devices 1, Make a call 1, Receive call 1

background image

English

Connect wires: ISO connectors

1

Pull out the ISO connectors from the car

dashboard and connect them to the bigger
end of the supplied standard connector.

2

Connect the other end of supplied standard

connector to the unit.

If necessary, connect the following:

Connector Connect to/with

1

Black cable

Antenna

2

Yellow cable Video out 1

3

Yellow cable Video out 2

4

Yellow cable Camera in

5

Green/white
wire

Parking

6

Black cable

Bluetooth microphone

7

Blue cable

Subwoofer

8

Red cable

Front line out L

9

White cable Front line out R

0

Red cable

Rear line out L

!

white cable Rear line out R

Mount in the dashboard

Note

Check wire connection before you mount

the unit into a car.
If preset radio stations are lost when the

ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.

1

If the car does not have an on-board drive or

navigation computer, disconnect the negative
terminal of the car battery.

If you disconnect the car battery in

a car that has an on-board drive or

navigation computer, the computer may
lost its memory.
If the car battery is not disconnected,

to avoid short-circuit, ensure that bare
wires do not touch each other.

2

Ensure that car dashboard opening is within

these measurements:

Since the unit cannot be used if the

dashboard opening’s slant angle is above
20 degrees: Ensure that the horizontal
slant of the car dashboard opening is
between 0 and 20 degrees

3

Remove the screws on the both side of the

unit.

4

Remove the mounting sleeve.

5

Install the sleeve into the dashboard and

bend the tabs outward to fi x the sleeve.

6

Place the rubber cushion over the end of the

bolt.

7

Slide the unit into the dashboard until a click

sound is heard.

If the unit cannot fi t into the dashboard,

remove the mounting bracket on the
both side of the unit and replace them
with the supplied short mounting
brackets.

8

Attach the trim plate.

9

Reconnect the negative terminal of the car

battery.

Turn on

1

Press the to turn on the unit.

The screen opens automatically.

»

The available OSD (On-Screen Display)

»
languages are displayed.

2

Touch a language to select.

The OSD language is changed to the

»
selected language immediately.

To adjust the screen tilt, press

TILT .

To close the screen, press

OPEN/CLOSE .

To adjust the brightness/contrast, press

/ ,

then adjust 4 WAY NAVIGATION .
To turn off the system, press

for 3 sec-

onds.

The screen closes automatically.

»

Set clock

1

Touch to display main menu.

2

Touch

[Setting].

The setup menu is displayed.

»

3

Touch

[General].

4

Touch

the

[Clock mode] repeatedly to

select:

[12hr]

: 12 hour mode

[

24hr] : 24 hour mode

5

Touch the hour digits, then touch or .

6

Touch the minute digits, then touch or .

7

If 12 hour mode is selected, touch or

to select AM or PM .

8

Touch

to exit.

Tune to a radio station

1

Touch

to display the main menu.

2

Touch

[Radio].

Band and frequency information is

»
displayed.

3

Touch

[Band] repeatedly to select:

FM band options:

FM1, FM2, FM3

AM band options:

AM1, AM2

4

Briefl y touch [Previous] or [Next] to tune

to a radio station by step.

Play discs

1

Insert the disc into the disc slot with label

side facing up.

Play starts automatically.

»

To remove the disc, press the

»

button.

When the disc is ejected, the unit switches

»
to the previous source, if connected. Other-
wise, the unit switches to [Radio] mode auto-
matically.

Insert USB or SD/MMC card

1

Open the USB/SD/MMC card cover.

2

Insert the USB device or SD/MMC card into

the USB socket or SD/MMC card slot.

Play starts automatically.

»

Pair the Bluetooth-enabled

devices

1

Turn on the Bluetooth function on the

device.

2

Setup the Bluetooth function on your device.

3

Select “CED750” in the pairing list.

4

Enter default password “0000”.

iI pairing succeeds.

»

[Connect] is displayed

on the panel.

Make a call

1

Pair the phone with the system.

2

Touch

to return to main menu.

3

Touch

[Bluetooth].

The Bluetooth menu is displayed.

»

4

Touch

to dial.

Receive call

1

If there is incoming call, [Incoming call…]

fl ashes on the screen. Speak into the Blue-
tooth microphone.

2

When conversation ends, touch to

terminate the call.

3

Prin

tin

g in

C

hin

a

Prin

tin

g in

C

hin

a

4

© 2008 Koninklijke Philips Electronics N.V.

All rights reserved.

CED750 QSG_Eng.indd 2

CED750 QSG_Eng.indd 2

2008-12-12 16:05:30

2008-12-12 16:05:30