Pioneer SUPERTUNERD DEH-P5200HD - Manual (Page 15)

SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
! When selecting FM as the source, you cannot
switch to SLA.
! Settings are based on the FM volume level, which
remains unchanged.
Before adjusting source levels, compare the FM
volume level with the level of the source you wish
to adjust.
! The AM volume level can also be adjusted with
source level adjustments.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to
–4
3 Press M.C. to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
Initial Settings
1 Press SRC/OFF and hold until the unit
turns off.
2 Press M.C. and hold until the initial set-
ting menu appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
Clock (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock dis-
play you wish to set.
Hour
—Minute
As you select segments of the clock display, the
selected segment flashes.
3 Turn M.C. to adjust the clock.
Clock (clock on/off setting)
1 Press M.C. to turn the clock display on or off.
AUX1/AUX2 (auxiliary input setting)
Activate this setting when using auxiliary device con-
nected to this unit.
1 Press M.C. to turn AUX on or off.
USB PnP (plug and play)
This setting allows you to switch your source to USB/
USB-iPod automatically.
1 Press M.C. to turn the plug and play on or off.
ON – When USB storage device/iPod is con-
nected, the source is automatically switched to
USB/USB-iPod. If you disconnect your USB sto-
rage device/iPod, this unit
’s source is turned off.
OFF – When USB storage device/iPod is con-
nected, the source is not switched to USB/USB-
iPod automatically. Please change the source to
USB/USB-iPod manually.
Brightness (display brightness setting)
1 Press M.C. to display the setting mode.
2 Turn M.C. to switch the brightness setting.
High (high) —Low (low)
3 Press M.C. to confirm the selection.
SW control (rear output and subwoofer setting)
The rear speaker leads output ( Rear SP) and RCA out-
put ( Preout) of this unit can be used for full-range
speaker ( Rear SP :FULL/Preout :Rear) or subwoofer
( Rear SP :SUBW/Preout :SUBW) connection. If you
switch to Rear SP :SUBW, you can connect a rear
speaker lead directly to a subwoofer without using an
auxiliary amp.
Initially,
Rear SP is set for rear full-range speaker con-
nection ( FULL). When Rear SP :FULL is selected, you
can connect the RCA output to a subwoofer. In this
case, you can select whether to use the subwoofer
controller
’s (low pass filter, phase) built-in Preout :
SUBW or the auxiliary Preout :Rear.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between as following:
Rear SP/Preout —FULL (SUBW)/SUBW(Rear)
3 Turn M.C. to change the setting.
Rear SP: FULL
—SUBW
Preout: SUBW —Rear
! Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
SW setting 1 (subwoofer on/off
setting) on the previous page).
! If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
DEMO (demo display setting)
1 Press M.C. tp turn the demo display on or off.
En
15
English
Section
02 Operating this unit