Philips VR530/07 - Manual (Page 5)

Manual TV channel search
In some cases it can occur that all of the TV
channels are not found and saved during the first
installation. In this case, the missing or coded TV
channels must be searched for and stored man-
ually.
1. 1. Switch on the TV set. If required, select the
programme number for the video recorder.
2. 2. Press .
The main menu will appear.
3. 3. Use to select 'TUNER SET UP'.
Then press .
4. 4. Use to select 'MANUAL TUNING'.
Then press .
5. 5. Select 'PROG.' with . Then press
.
6. 6. With or , select the desired
programme number that you want to use for
the TV channel, e.g. 'P01'. Then press
.
7. 7. Select 'CHANNEL' with , and con-
firm with . Then enter the desired chan-
nel with .
If you set 'SKIP' on for a channel, this channel
will be ignored when going through the channels
with or .
8. 8. Save the TV channel with .
9. 9. To search for other TV channels, begin again
at step 5.
10. 10. To end, press .
Using the satellite receiver
Satellite channels from a satellite receiver (con-
nected to the scart socket AV2(DECODER) ) are
received on the video recorder on programme
number 'AV2' with 0.0.2.
You should select the satelite channels to be
received by the satellite receiver directly on the
receiver itself.
Sorting TV channels automatically
(Follow TV)
When the automatic channel search function is
activated, the TV channels are saved in a specific
order. This may vary from the order of TV chan-
nels on the TV.
This function changes the order of TV channels
saved in the video recorder to match that of the
TV.
Make sure that the video recorder and the TV
are connected by a scart cable.
1. 1. Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2. 2. Press . The main menu will appear.
3. 3. Select 'TUNER SET UP' with and
confirm with .
4. 4. Select 'FOLLOW TV' with and
confirm with .
5. 5. 'P:01' will appear in the video recorder dis-
play.
6. 6. Select programme number '1' on the TV.
7. 7. Confirm with on the video recorder
remote control. The video recorder compares
the TV channels on the TV and the video
recorder.
If the video recorder finds the same TV chan-
nel as on the TV, then it stores it at 'P01'.
B 1
B 1
L C K B
B 1
L C K B
MENU
STATUS/EXIT
B 1
P– P+
0..9
B 1
L C K B
B 1
0..9 L C K B
B 1
L C K B
B 1
L C K B
B 1
L C K B
MENU
5 EN
MANUAL TUNING
→PROG. P55
CHANNEL 055
DECODER [OFF]
SKIP [OFF]
SELECT K L CHOOSE B
END=EXIT
What is a special channel?
TV channels are transmitted in certain pre-
defined frequency ranges. These ranges are
divided into channels.
A specific frequency/channel is assigned to each
TV station.
Certain frequency ranges are specified as special
channels (hyperband channels).
I don't know the channels for my TV stations
In this case, press
in 'CHANNEL' to
start the automatic channel search. A changing
channel number will appear on the TV screen.
Continue the automatic search until you have
found the desired TV channel.
L C K B
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
END=EXIT
I cannot switch my TV set to programme
number '1'
* If you have connected additional devices to
socket AV2(DECODER), please disconnect
these devices. Because of other connected
devices, the TV set could switch to the pro-
gramme number of the scart socket.
HC461BD.qxp 02.2.6 10:12 AM Page 5