Polk Audio Pol Audio LC265i - Manual (Page 2)

P E R F O R M A N C E
OVERALL FREQ. RESPONSE 20Hz-27kHz
FREQ. RESPONSE -3DB LIMIT 35Hz-27kHz
ANALOG AUDIO SIGNAL
VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT 2V RMS
AMPLIFIER SNR > 90DB
FIRMWARE UPGRADABLE YES
MID-BASS DRIVER 1–6.5"(16.5CM) MINERAL POLYPROPYLENE
CONE, RUBBER SURROUND;
WOOFER 1–6.5"(16.5CM) AERATED POLY-
PROPYLENE CONE WITH 1.5" VOICE COIL
TWEETER 1" (2.5CM) RING RADIATOR IN SWIVEL MOUNT
OUTSIDE DIMENSIONS 8 1/2" X 20 7/8" (21.59CM X 53.04CM)
CUTOUT DIMENSIONS 7 1/4" X 19 1/4" (18.42CM X 48.90CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL) 3 1/16" (7.78CM)
INSTALLED WEIGHT 8.7 LBS (3.9kg)
SHIPPING WEIGHT 11.6 LBS (5.3kg)
P O W E R C O N T I N U O U S R AT I N G S
200W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid
8 Ohms, 100W woofer 8 Ohms)
P O W E R R E Q U I R E M E N T S P E R S P E A K E R
VOLTAGE INPUT 48VDC
CURRENT DRAW 4.5A MAXIMUM
LC265i-IP Specifications
2 P o l k A u d i o C u s t o m I n s t a l l P r o d u c t : L C 2 6 5 i - I P , L C 8 0 i - I P w w w . P o l k A u d i o . c o m / 8 0 0 . 3 7 7 . 7 6 5 5 ( U S A & C a n a d a ) / 4 1 0 . 3 5 8 . 3 6 0 0 ( W o r l d w i d e ) 3
Cutout
Dimension
9 7/16"
(23.9 cm)
Total
Depth
7 7/16"
(18.9 cm)
LC80i-IP Dimension
Outer Diameter 10 3/4" (27.3cm)
Available Finish: Paintable White
LC80i-IP Specifications
P E R F O R M A N C E
OVERALL FREQ. RESPONSE 25Hz-27kHz
FREQ. RESPONSE -3DB LIMIT 40Hz-27kHz
ANALOG AUDIO SIGNAL
VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT 2V RMS
AMPLIFIER SNR > 90DB
FIRMWARE UPGRADABLE YES
MID-BASS DRIVER 1–8"(20.3CM) COMPOSITE POLYPROPYLENE
CONE, RUBBER SURROUND
TWEETER 1"(2.5CM) RING RADIATOR IN SWIVEL MOUNT
OUTSIDE DIMENSIONS 10 3/4" DIA (27.3CM)
CUTOUT DIMENSIONS 7 3/8" DIA (18.7CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL) 6 15/16" (17.6CM)
INSTALLED WEIGHT 4.8 LBS (2.2kg)
SHIPPING WEIGHT 6.8 LBS (3.1kg)
P O W E R C O N T I N U O U S R AT I N G S
100W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid
4 Ohms)
P O W E R R E Q U I R E M E N T S P E R S P E A K E R
VOLTAGE INPUT 48V OR 28VDC
CURRENT DRAW 2.3A @ 48V, OR
3.8A @ 28V MAXIMUM
I N H E R E N T D E L AY
INHERENT DELAY FOR EACH SPEAKER IS:
-2.5 MILLISECONDS -4.4 MILLISECONDS
ANY OTHER DELAY IS FROM THE MULTI-ROOM AUDIO VISUAL (MRAV).
P R O T E C T I O N C I R C U I T R Y
Thermal, short-circuit, current overdraw,
clipping compresser/limiter, reverse polarity
C O N T R O L S A N D A D J U S T M E N T S
(Performance Optimization Wizard Program)
COMPUTER REQUIREMENTS
OPERATING SYSTEM WINDOWS XP
USB PORT 5-WIRE USB 1.1 CONNECTOR
HARD DRIVE 5 MEGABYTES
REQUIRED SPEAKER CONNECTIONS
TO CONNECT YOUR COMPUTER TO THE SPEAKER, YOU HAVE TWO OPTIONS:
1. USB PORT (ANALOG USE ONLY)
2. ETHERNET JACK WITH NETWORK DECODER CARD (SOLD SEPARATELY).
LC265i-IP and LC80i-IP Specifications
IEC Socket
This is a standard
IEC socket.
Power Connectors
For optimum performance, we recommend using 14-gauge,
4-conductor wire between the power supply and each
amplifier (see the LCi-IP manual for other wiring options).
Note: Leave at least 2-3 inches
of clearance on the sides and
top of the power supply.
LC80i-IP Hardware
• One LC80 i-IP speaker
• Performance Optimization Wizard – CD-ROM
• Euro-style (Phoenix) power supply connector
• Mounting template
• Paint mask
• Weather-resistant aluminum grille
and stainless steel hardware
• LC i-IP manual
• Laminated configuration setup card
• Registration card
Note: If you are setting up LCi-IP speakers to be controlled via an
IP-network such as NetStreams
™ Digilinx ™ , purchase a network card, which
is sold separately, from NewStreams ™ . The network card will control up to
one pair of speakers.
Important Note: If anything is missing or damaged, or if your LCi-IP speak-
er fails to operate, notify Polk Audio Installer Support Services
immediately at 800-377-7655.
Accessories (not included)
• Performance Enclosure for exact volume enclosure performance
in pre-build installations. Improves bass performance and
sound isolation. Model number: ENCL 80IP.
• Speaker-level-to-line-level transformer, such as the PAC SNI-35.
(For analog installations only. Powers up to 4 each LC80i-IP speakers.)
• SPS-1 Power Supply (a power supply is required).
Power Supply
The SPS-1 power supply was specifically designed to produce clean,
reliable power to ensure that all Polk Audio LCi-IP loudspeakers perform
to their maximum capabilities. All output connectors are protected
against short circuit and over current.
Specifications
Output
Voltage
48VDC
Current 8A (Max continuous)
Input
Voltage Range
100-240 VAC Nominal Auto Switching
Frequency 50-60Hz
Current Draw
8A (120V)
3.5A (240V)
Dimensions
Width
4.9" (125mm)
Height 3.1" (79mm) , 3 11/16"(93.6mm) with feet
Length 14" (358mm)
Shipping Weight 8.4lbs (4kgs)
Protection Thermal, short circuit, current/power overdraw
Fuse Replacement T8AH500V
LC80i-IP Performance Enclosure Dimensions
20 5/8" H x 13" W x 9" D (51.8cm x 33.0cm x 22.9cm)
Capabilites
SPS-1 will power 2 LC265i-IP speakers or 4 LC80i-IP speakers.