Panasonic AK-MSU930P - Manual (Page 8)

8
Parts and their functions
MONI LINK: Shading link setting
This is used to set whether to link the
monitor when the R, G or B shading
switch has been selected.
ANALOG: CCU analog output setting
This is used to set the analog output of
the CCU to the HD or SD component.
SDI4 OUT: HD SDI4 output selection
This is used to set the HD SDI4 output of
the CCU as the PM or normal output.
SYNC: Sync waveform addition setting
This is used to select whether to add the
sync waveform to the analog output.
TYPE: Analog sync waveform setting
This is used to set the sync waveform to
be added to the HD analog output to
binary or tri-level.
H_CO (HDTV): Horizontal sync signal phase coarse
adjustment
This is used to coarsely adjust the phase
in relation to the HDTV genlock sync
signal.
H_FIN (HDTV): Horizontal sync signal phase fine
adjustment
This is used to finely adjust the phase in
relation to the HDTV genlock sync signal.
H_CO (SDTV): Horizontal sync signal phase coarse
adjustment
This is used to coarsely adjust the phase
in relation to the SDTV genlock sync
signal.
H_FIN (SDTV): Horizontal sync signal phase fine
adjustment
This is used to finely adjust the phase in
relation to the SDTV genlock sync signal.
SCCO: Subcarrier phase coarse adjustment
This is used to coarsely adjust the phase
of the subcarrier signal in relation to the
SDTV genlock sync signal.
SCFIN: Subcarrier phase fine adjustment
This is used to finely adjust the phase of
the subcarrier signal in relation to the
SDTV genlock sync signal.
SH_H: SD/HD horizontal phase
This is used to adjust the horizontal
phase of the SDTV output and HDTV
output.
SH_V: SD/HD vertical phase
This is used to set the vertical phase of
the SDTV output and HDTV output to
line 0 and line 90 (advanced by 90H for
HDTV).
Pedestal control switch [PED CONTROL]
This is selected to adjust the R, G and B pedestal levels
in relation to the master pedestal position.
When it is selected, its lamp lights.
GPED:
G pedestal level
Adjustment range: –100 to +100 (amount
of G pedestal offset
from master pedestal)
RPED, BPED: R, B pedestal level
Adjustment range: –100 to +100
The level is increased or decreased from
the level at the pedestal position where
the black balance was attained.
When the black balance is adjusted, 0 is
set as the adjustment value.
Gain control switch [GAIN CONTROL]
This is selected to adjust the white balance. When it is
selected, its lamp lights.
G GAIN:
Adjustment range: –100 to +100
(Amount by which the G gain is to be
increased or decreased from its
reference setting)
R GAIN, B GAIN: Adjustment range: –100 to +100
(Amount by which the R or B gain is to
be increased or decreased as
referenced to their levels at the
pedestal position where the white
balance was attained; when the white
balance is adjusted, 0 is set as the
adjustment value.)
Gamma curve control switch [GAMMA CONTROL]
This is selected to adjust the gamma correction.
Since the M GAM adjustment value is independent of the
R and B GAM adjustment values, the R and B GAM
values remain unchanged even when M GAM is
changed.
When the switch is selected, its lamp lights.
M GAM:
Master gamma
Adjustment range: 0.600 to 0.300
RGAM, BGAM: Adjustment range: –75 to +75
Flare control switch [FLARE CONTROL]
This is selected to change the amount of flare correction.
When it is selected, its lamp lights.
RFLR, GFLR, BFLR: R, G and B flare
Adjustment range: –50 to +50
(Flare correction operation is
turned off at 0.)
White clip control switch [WHITE CLIP CONTROL]
This is valid when the lamp of the WHT CLIP OFF switch
among the MODE ON/OFF switches is off, and it is
selected to change the white clip level. When it is
selected, its lamp lights.
WHT CLIP: White clip
Adjustment range: 95% to 110%
Knee control switch [KNEE CONTROL]
This is selected to adjust the knee slope and knee point.
MPNT:
Master knee point
Adjustment range: 105% to 85%
RPNT, BPNT: R and B knee points
Adjustment range: +10% to –10%
MSLP: Master knee slope
Adjustment range: 63 to 0
RSLP, BSLP: R and B knee slopes
Adjustment range: +32 to –31