Pioneer VSX-2014i - Manual (Page 33)

Listening to your system 05
33
En
Listening with Acoustic Calibration
EQ
• Default setting: OFF / ALL CH ADJ (after the Auto
MCACC Setup or EQ Auto Setting)
You can listen to sources using the Acoustic Calibration
Equalization set in
Automatically setting up for surround
sound (MCACC) on page 11 or Acoustic Calibration EQ on
page 41. Refer to these pages for more on Acoustic
Calibration Equalization.
The illustration above shows the VSX-2014i model.
• While listening to a source, press ACOUSTIC EQ.
Press repeatedly to select between:
• ALL CH ADJ – No special weighting is given to any
one channel.
• FRONT ALIGN – All speakers are heard in
accordance with the front speaker settings.
• CUSTOM 1/2 – Custom settings
• OFF – Switches Acoustic Calibration EQ off.
The MCACC indicator on the front panel lights when
Acoustic Calibration EQ is active.
Note
• You can’t use Acoustic Calibration EQ when MULTI
CH IN is switched on, and it has no effect when
headphones are connected.
• If you switch on Acoustic Calibration EQ when
DIRECT is selected, the receiver automatically
switches to STEREO .
Choosing the input signal
You need to hook up a component to both analog and
digital inputs on the rear of the receiver to select between
input signals.
The illustration above shows the VSX-2014i model.
• Press SIGNAL SELECT to select the input signal
corresponding to the source component.
Each press cycles through the options as follows:
• AUTO – The receiver selects the first available signal
in the following order:
(VSX-2014i only); DIGITAL ; ANALOG .
• ANALOG – Selects the analog inputs.
• DIGITAL – Selects the digital input.
• (VSX-2014i only) – Selects the i.LINK input.
When set to DIGITAL or AUTO , 2 DIGITAL lights when
a Dolby Digital signal is input, and DTS lights when a DTS
signal is input.
Note
• This receiver can only play back Dolby Digital, PCM
(32kHz–96 kHz) and DTS digital signal formats
(including DTS 96kHz/24 bit). With other digital
signal formats, set to
ANALOG .
VSX-2014i only – If you are using the i.LINK
connectors, DVD-A (including 192 kHz) and SACD
are also supported.
• You may get digital noise when a LD or CD player
compatible with DTS is playing an analog signal. To
prevent noise, make the proper digital connections
(page 16) and set the signal input to
DIGITAL .
• Some DVD players don’t output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
RECEIVER CONTROL
SHIFT
THX
SLEEP DIALOG E
AUTO SURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CH SEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER CONTROL
TUNER EDIT
SYSTEM
SETUP RETURN CONTROL ON/OFF MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
PTY SEARCH BAND EON TONE ACOUSTIC
EQ
i.LINK
SELECT
MULTI CH
IN
SIGNAL
SELECT EXTENDED
MODE SPEAKERS
MULTI JOG MULTI JOG MULTI JOG MULTI JOG
RECEIVER CONTROL
SHIFT
THX
SLEEP DIALOG E
AUTO SURR
STANDARD ADV.SURR STEREO
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
SIGNAL
SELECT
EFFECT
/CH SEL
ACOUSTIC
EQ
HDD
CH CH
DVD
RECEIVER
PHONES
TUNER CONTROL
TUNER EDIT
SYSTEM SETUP RETURN CONTROL ON/OFF MCACC
SETUP MIC
DIGITAL IN S-VIDEO VIDEO
VIDEO2 INPUT
AUDIO L R
MULTI ROOM
MULTI JOG MULTI JOG
TUNING/ STATION BAND TONE ACOUSTIC EQ MULTI CH IN SIGNAL
SELECT EXTENDED MODE SPEAKERS
MULTI JOG MULTI JOG
PTY SEARCH EON i.LINK SELECT
MULTI JOG MULTI JOG
VSX_2014TX.book.fm Page 33 Wednesday, June 2, 2004 5:21 PM