Filter mode, Continued), Programming cycles per day – Pentair Variable Speed Pump IntelliFlo User Manual

Page 23: Intelliflo, 00 am, 59 am, 15 am, Intelliflo installation and user’s guide

IntelliFlo Installation and User’s Guide

Filter Mode

(Continued)

To set the Cycles Per Day:

Press the Select button to access the “Cycles Per Day” setting. To edit

this setting, see step 6.

IntelliFlo uses the Cycles Per Day parameter to calculate how much time it has to
complete its filter job. You can program up to four start and stop cycles per day.
The more time the IntelliFlo is given to operate the less power and flow will be
needed for turning over the pool.

Note: Consumers in certain areas are charged lower energy rates at non-peak
hours. To take advantage of this, the IntelliFlo can be programmed to run at
any time of the day. The extremely quiet operation of the IntelliFlo makes it
feasible to operate during the early morning or late at night. The easiest and
best way to optimize flow during filter cycles is by adding or subtracting cycle
time. This way, the desired flow effect, for example, skimming action, can be
achieved while maintaining the desired water turnover rate.

6. Press the Select button to change the current value.

7. To change the value, press the Left and Right arrows to select which digit to modify, then use the Up

and Down arrows to change the selected digit.

8. When you are done, press the Enter button to save the changes. To cancel any changes, press the

Escape button to exit edit mode without saving.

Programming Cycles Per Day

Each cycle has two screens, one for the “Start Cycle” and one for “Stop Cycle”. The following examples
shows one for the cycle start/stop time. Only one cycle is entered in the “Cycles Per Day” parameter.

Filter

Vacuum

Back

Wash

Manual

Enter

Select

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:08

Cycles Per Day

This screen shows the filter
cycle as “Disabled” for a start/
stop cycle (Cycles Per Day
programmed to 1). These
screens will still display even
if they are not enabled.

Enabled or disabled is
displayed depending on
how many cycles are
selected

Start and Stop
Cycle is displayed

Filter

Vacuum

Back

Wash

Manual

Enter

Sele

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:02

Stop Cycle 1

Stop Cycle 1
Enabled

Enabled

9:00

9:00 pm

Filter

Vacuum

Back

Wash

Manual

Enter

Sele

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:10

Start Cycle 2

Start Cycle 2
Disabled

Disabled

9:10

9:10 pm

Filter

Vacuum

Back

Wash

Manual

Enter

Sele

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:01

Start Cycle 1

Start Cycle 1
Enabled

Enabled

9:00 am

This screen shows the filter
cycle as “Disabled” for a start/
stop cycle (Cycles Per Day
programmed to 1). These
screens will still display even
if they are not enabled.

Enabled or disabled is
displayed depending on
how many cycles are
selected

This example will
run the pump for 24
hours. Start and
Stop Cycle is
displayed

Filter

Vacuum

Back

Wash

Manual

Enter

Select

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:02

Stop Cycle 1
Enabled

7:59 am

Filter

Vacuum

Back

Wash

Manual

Enter

Select

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:10

Start Cycle 2
Disabled

10:15 am

Filter

Vacuum

Back

Wash

Manual

Enter

Select

Start
Stop

Reset

Feature

Men

Escape

Warn.

Alarm

IntelliFlo

Filter

12:01

Start Cycle 1
Enabled

8:00 am