Poulan Pro PP400E User Manual

Page 3

Keep the handles dry and clean and

free from oil and grease.

Keep oil cap and fasteners securely

tightened.

Nonconforming replacement compo-

nents or the removal of safety devices

may cause damage to the unit and pos-

sible injury to the operator or bystand-

ers. Use only Poulan PRO accessories

and replacement parts as recom-

mended. Never modify your saw.

Maintain chain saw with care.

Keep unit sharp and clean for better and

safer performance.

Follow instructions for lubricating and

changing accessories.

Unplug the chain saw from the power

source when not in use, before servic-

ing, and when changing accessories

and attachments, such as saw chain

and guard.

Check for damaged parts. Before fur-

ther use of the chain saw, a guard or

other part that is damaged should be

carefully checked to determine that it will

operate properly and perform its in-

tended function. Check for alignment of

moving parts, binding of moving parts,

breakage of parts, mounting and any

other conditions that may affect its op-

eration. A guard or other part that is

damaged should be properly repaired

or replaced by an authorized service

dealer unless otherwise indicated else-

where in the instruction manual.

When not in use, chain saws should be

stored in a dry, high or locked-up place

out of the reach of children.

When storing saw, unplug and use a bar

sheath or carrying case.

ELECTRICAL SAFETY

WARNING:

Avoid a dangerous

environment. To reduce the risk of elec-

trical shock, do not use in rain, in damp

or wet locations, or around swimming

pools, hot tubs, etc. Do not expose to

snow, rain, or water to avoid the possibil-

ity of electrical shock. Do not handle ex-

tension cord or plug with wet hands.
S

Use a voltage supply as shown on the

nameplate of the unit.

Avoid dangerous situations. Do not use

in the presence of flammable liquids or

gases to avoid creating a fire or explo-

sion and/or causing damage to unit.

To reduce the risk of electrical shock,

this appliance has a polarized plug (one

blade is wider than the other) and will re-

quire the use of a polarized extension

cord. The appliance plug will fit into a po-

larized extension cord only one way. If

the plug does not fit fully into the exten-

sion cord, reverse the plug. If the plug

still does not fit, obtain a correct polar-

ized extension cord. A polarized exten-

sion cord will require the use of a polar-

ized wall outlet. This plug will fit into the

polarized wall outlet only one way. If

plug does not fit fully into the wall outlet,

reverse the plug. If the plug still does not

fit, contact a qualified electrician to install

the proper wall outlet. Do not change the

equipment plug, extension cord recep-

tacle, or extension cord plug in any way.

To reduce risk of electrical shock, use

extension cords specifically marked as

suitable for outdoor appliances. The

electrical rating of the cord must not be

less than the rating of unit. The cord

must be marked with suffix “W--A” (in

Canada, “W”). Use a polarized cord.

Make sure your extension cord is in

good condition. Inspect extension cord

before use and replace if damaged. Do

not use a damaged cord. Cord insula-

tion must be intact with no cracks or de-

terioration. Plug connectors must be

undamaged. An undersized extension

cord will cause a drop in line voltage re-

sulting in loss of power and overheating.

If in doubt, use the next heavier gauge.

The lower the gauge number, the heavi-

er the cord (see

SELECT AN EXTENSION

CORD

in the

OPERATION

section). Do

not use multiple cords.

Do not abuse cord. Never carry the unit

by the extension cord or yank extension

cord to disconnect unit.

Secure extension cord to power cord to

prevent disconnection from unit.

Do not use the unit if the switch does not

turn the unit on and off properly, or if the

lockout does not work. Repairs to the

switch must be made by an authorized

service dealer.

Keep extension cord clear of operator

and obstacles at all times. Position cord

so that it will not be caught on branches.

Do not expose cords to heat, oil, water,

or sharp edges.

To avoid the possibility of electric shock,

avoid body contact with any grounded

conductor, such as metal fences or

pipes.

Ground Fault Circuit Interrupter (GFCI)

protection should be provided on circuit

or outlet to be used. Receptacles are

available having built-in GFCI protection

and may be used for this measure of

safety. Inspect chain saw cords periodi-

cally and if damaged, have repaired by

an authorized service dealer.