Lennox Hearth Gas Conversion Kit FGCK - Manual

1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
In Canada
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENT AUX RECOMMANDATIONS
DES AUTORITÉS PROVINCIALES AYANT
JURIDICTION ET CONFORMÉMENT AUX
EXIGENCES DU CODE D'INSTALLATION CAN1-
B149.1 ET.2.
This Gas Conversion Kit contains all of the
necessary components needed to complete the
conversion of an appliance from the use of one
type of gas to the use of another, including
labeling that must be affixed to ensure safe
operation.
ALWAYS REFER TO THE APPLIANCE INSTAL-
LATION AND HOMEOWNERS CARE AND OP-
ERATION DOCUMENTS BEFORE COMPLET-
ING A CONVERSION. ALL WARNINGS, CAU-
TIONS AND DETAILED INSTRUCTIONS CON-
TAINED THEREIN ARE APPLICABLE TO THIS
DOCUMENT.
Figure 1
GAS APPLIANCE
KITS AND ACCESSORIES
GAS CONVERSION KIT (FGCK)
Pressure
Regulator
Remove
These
Components
SIT VALVE
To complete the conversion proceed as follows:
Note: After converting the valve and gas compo-
nents, refer to the appliance installation and
homeowners care and operation instructions to
adjust the air shutter opening for the gas type used.
CAUTION: The gas supply shall be shut off
prior to disconnecting the electrical power,
before proceeding with the conversion.
Step 1. Turn off the gas supply to the appli-
ance. Remove the front glass door/frame (if
used) from the appliance. Access the control
compartment.
Step 2. Carefully remove the logs. Exercise
care as not to break the logs.
Step 3. Locate the screws securing the burner
(tray) to the appliance. Remove the burner
and retain the securing screws.
Millivolt Appliances
Step 4. SIT Systems - Refer to Figure 1. Using
a Torx T20, or a flat screwdriver, remove and
discard the three pressure regulator mounting
screws. Remove the pressure regulator, spring,
poppet, diaphragm and bushing.
Discard all removed components. Ensure the
rubber gasket installed on the back of the
replacement pressure regulator is properly
positioned and install the new pressure regula-
tor using the new screws supplied with this kit.
Tighten screws to 25 In. lb. torque.
WARNING: THIS CONVERSION KIT SHALL BE IN-
STALLED BY A QUALIFIED SERVICE AGENCY IN AC-
CORDANCE WITH THE MANUFACTURER'S INSTRUC-
TIONS AND ALL APPLICABLE CODES AND REQUIRE-
MENTS OF THE AUTHORIZED AGENCY HAVING JURIS-
DICTION. IF THE INFORMATION IN THESE INSTRUC-
TIONS ARE NOT FOLLOWED EXACTLY, A FIRE, EXPLO-
SION OR PRODUCTION OF CARBON MONOXIDE MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE. THE INSTALLATION IS NOT
PROPER AND COMPLETE UNTIL THE OPERATION OF
THE CONVERTED APPLIANCE IS CHECKED AS SPECI-
FIED IN THE OWNER INSTRUCTIONS SUPPLIED WITH
THE KIT. AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION SERA
INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SERVICE
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET
TOUTES EXIGENCES ET CODES APPLICABLES DE L'AUTORISÉS
AVOIR LA JURIDICTION. SI L'INFORMATION DANS CETTE
INSTRUCTION N'EST PAS SUIVIE EXACTEMENT, UN FEU,
EXPLOSION OU PRODUCTION DE PROTOXYDE DE CARBONE
PEUT RÉSULTER LE DOMMAGES CAUSER DE PROPRIÉTÉ,
PERTE OU BLESSURE PERSONNELLE DE VIE. L'AGENCE
QUALIFIÉE DE SERVICE EST ESPONSABLE DE L'INSTALLATION
PROPRE DE CET ÉQUIPMENT. L'INSTALLATION N'EST PAS
PROPRE ET COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL
CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS
DANS LES INSTRUCTIONS DE PROPRIÉTAIRE PROVISIONNÉES
AVEC L'ÉQUIPEMENT.
750,018M
REV. D 07/2007
Step 5. Honeywell Systems - See Figure 2.
Remove the black thread-protecting cap. Re-
move the conversion flip cap by turning it
counterclockwise. Invert the flip cap so that the
letters associated with the desired gas type are
positioned closest to the valve body.
NG is for natural gas and LP is for propane.
Tighten the flip cap by turning it clockwise.
Replace the black thread-protecting cap.