Lincoln Electric LN-8 SVM132-A - Manual (Page 40)

C-4 ACCESSORIES C-4
K240 CONTACTOR KIT
Output contactor with pilot relay to make the electrode
‘cold’ when not welding. Must be ordered when using
the LN-8 with SA-750, SAE, TM, R3M and R3R
Idealarcs. Contactor kits are rated at 600 amps maxi-
mum, and cannot be paralleled with each other.
K317 DUAL PROCESS KIT
(NO POLARITY CHANGE)
The Dual Process Kit is a transfer device that con-
nects two wire feeders to a single power source and
enables each wire feeder to weld a different proce-
dure without changing any of the dials. When used
with the DC-600, the wire feeders can be set for differ-
ent modes; CV Innershield or CV Submerged Arc.
Both wire feeders will operate at the same polarity.
K318 DUAL PROCESS CONTACTOR KIT
(WITH POLARITY CHANGES)
The Dual Process Contactor Kit permits the connec-
tion of two wire feeders to a single power source and
enables each wire feeder to weld at a different proce-
dure and polarity without changing any dials or switch-
es. When used with the DC-600, the wire feeders can
be set for different modes; CV Innershield or CV
Submerged Arc. The kit can also be connected to
operate with the same polarity on each wire feeder.
REEL MOUNTING ACCESSORIES
K303 50 TO 60 lb (22.7 TO 27.2 kg)
WIRE REEL STAND
This assembly includes a framework to which is
attached a 50 to 60 lb (22.7 to 27.2 kg) wire reel, a
mounting spindle, a lift bail, and a cable clamp for fas-
tening the input cable assembly.
K1524-1 UNIVERSAL REEL STAND
AND BASE ASSEMBLY
The wire reel stand comes with a 2 in. spindle. With
the addition of the proper spindle and Readi-Reel
adapters, it can accomodate various sizes of coils,
spools, and Readi-Reels.
K363P 30 lb Readi-Reel Adapter
K435 Spindle Adapter for 14 lb coils
K468 Spindle Kit
K1504-1 60 lb Wire Reel
K438 60 lb Readi-Reel Adapter
K162 SPINDLE FOR MOUNTING
READI-REELS AND 10 THRU 30 lb
(4.5 THRU 13.5 kg) SPOOLS
For use with the K303 wire reel stand. To mount this
spindle kit, remove the shaft from the standard 50 to
60 lb (22.5 to 27.2 kg) wire coils from the mounting
framework. Install the spindle per the instructions
shipped with the kit.
K377 SMALL MOUNTING STAND FOR
READI-REEL COILS OR 10 THRU 30 lb
(4.5 THRU 13.5 kg) SPOOLS WITH 2 in.
(50 mm) I.D.
This assembly includes a wire reel spindle (similar to
the K162 spindle) attached to a small frame. The unit
is supplied with the K363 Readi-Reel Adapter for
using the Lincoln “Readi-Reel Electrode Coils”.
Without the adapter, the unit is capable of handling
spools with a 2 in. I.D., a 12 in. maximum O.D., and a
4 in. width. The spindle has an adjustable breaking
system.
K378 SMALL MOUNTING STAND FOR
13 TO 14 lb (6.0 TO 6.4 kg)
INNERSHIELD COILS
This assembly includes the smaller frame as used in
the K377 and the fully enclosed canister system for
derailing of the 14 lb coil. This system has a fixed
brake for the 14 lb coil.
M11514 WIRE REEL DUST SHIELD DOOR
FOR K303
In extremely dusty and dirty locations, this door kit can
be added to those units having a dust shield kit
(S14543). This door kit includes a hinged door and
sliding bottom seal. When these parts are attached to
the reel support per the instructions included, the unit
becomes a completely enclosed housing. Order part
no. M11514.
LN-8
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC