beautypg.com

Modelo 2648, Funcionamiento, Step 1: pipe assembly step 2: stand assembly – Lasko 2648 User Manual

Page 3: Step 4: blade & grill assembly, Step 3: head assembly, Caution

background image

MODELO 2648

FUNCIONAMIENTO

este Ventilador puede hacerse funcionar mediante los
Controles manuales ubicados en la parte superior de la
unidad (como se muestra en la Figura 9) o con el Control
remoto (se muestra en la Figura 12).
1. Conecte el cable eléctrico a un tomacorriente de 120

V~.

Asegúrese que el enchufe encaje firmemente en el

tomacorriente.

Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial
o completamente fuera del tomacorriente
con un leve movimiento del cable adosado.
los tomacorrientes en este estado podrían
sobrecalentarse y representar un grave
peligro de incendio; si está cubierto por una
cortina o tela, el riesgo de incendio es aún
mayor.

2. Conecte la energía eléctrica a su ventilador pulsando el

Botón Alimentación ( ).

3. VELOCIDAD DEL VENTILADOR: ahora puede ajustar la

velocidad del ventilador al nivel deseado -baja, mediana
ó alta - pulsando el Botón Velocidad ( ).

4. OSCILACION: empuje la perilla ubicada en la parte su-

perior de la caja del motor para hacer que la cabeza del
Ventilador se mueva de un lugar hacia otro. (Figuras 10 y 11)

5. después de apagar el Ventilador, desconecte la unidad

del tomacorriente eléctrico.

new 9/11

10

2084237

new 9/11

3

2084237

1. take pipe assembly out of carton as shown.

(Figure 1)

2. loosen Height Adjustment Nut turning counter clockwise.

(Figure 2)

3. raise Extension Pipe.

(Figure 3)

4. tighten Height Adjustment Nut turning clockwise.

(Figure 4)

STEP 1: PIPE ASSEMBLY

STEP 2: STAND ASSEMBLY

PLACE BASE FLAT ON FLOOR

1. With a twisting motion, insert the end of the large diameter

pipe into hole in Base. (Figure 5) turning pipe while pushing

will assure pipe is fully seated in Base.

2. For Height adjustment:

a) loosen Height Adjustment Nut.

b) raise or lower Extension Pipe to desired height.

c) tighten Height Adjustment Nut.

1. Place Head Assembly with

Collar onto Extension Pipe.
(Figure 6)

2. Holding Extension Pipe

firmly, twist Head Assembly
downward until seated on
Extension Pipe.

1. tilt Head Assembly back. Put Rear Grill on motor. (Figure 7)
2. align tab of Plastic Rear Grill with groove on top of front

Motor cover.

STEP 4: BLADE & GRILL ASSEMBLY

3. Fully seat Rear Grill and secure with Plastic Nut turning Clock-

wise. slide Blade onto Motor Shaft. (Figure 8) align Groove on

blade hub with Pin on motor shaft. (Figure 8A)

4. to secure Blade, screw Spinner onto shaft Counter

Clockwise until tight on Blade hub.

STEP 3: HEAD ASSEMBLY

Head

Assembly

Collar

Extension

Pipe

Figure 6

Botón

Alimentación

Figura 9

Figure 2

Figure 4

Figure 3

Figure 1

Height

Adjustment

Nut

Extension

Pipe

Rear

Grill

Figure 7

Motor

Rear Grill

Figure 8

Blade

Fan

Spinner

Plastic

Nut

Figure 8A

Pin

Groove

Hacia Arriba: Estacionario

Hacia Adelante: Oscilar

Figura 10

Figura 11

Botón

Velocidad del

Ventilador

5. With fan head in upright position, align ornament of Front Grill

so it is horizontal and right side up. By starting with the top of

the grill and working down, snap Grill in place. NO GRILL CLIPS

ARE NEEDED FOR ASSEMBLY.

Extension Pipe

Height

Adjustment Nut

Base

CAUTION:

When making height adjustment after
head assembly is attached,
alWays support extension pipe
with one hand, as loosening height
adjustment nut may otherwise cause
rapid fall of extension pipe and head
assembly.

Figure 5

a

B

do not take pipe
apart. should pipes
become separated,
insert pipe a into
pipe B.