Setup – Linn EXOTIK PRE-AMPLIFIER User Manual
Page 18
Setup
SLEEP TIMEOUT
Set the time elapsed before the front panel display enters sleep mode (i.e. shows three
dots) after a key on the front panel or handset is pressed.
Options: N
NE
EV
VE
ER
R S
SL
LE
EE
EP
P,, IIM
MM
ME
ED
DIIA
AT
TE
E,, 3
30
0 S
SE
EC
C..,, 5
5 M
MIIN
NS
S..
Default setting: N
NE
EV
VE
ER
R S
SL
LE
EE
EP
P
STARTUP SOURCE
Set the source the unit selects when brought out of standby.
Options: L
LA
AS
ST
T U
US
SE
ED
D,, N
NO
ON
NE
E,, ((a
an
ny
y o
off tth
he
e s
so
ou
urrc
ce
e iin
np
pu
utts
s))
Default setting: L
LA
AS
ST
T U
US
SE
ED
D
STANDBY RECORD FROM
You can record from a source component to a recording device through the EXOTIK,
even if the EXOTIK is in standby mode.
Set which source configuration you want the EXOTIK to select when it is in standby.
Options: L
LA
AS
ST
T U
US
SE
ED
D,, N
NO
ON
NE
E,, ((a
an
ny
y o
off tth
he
e s
so
ou
urrc
ce
e iin
np
pu
utts
s)),, A
AS
S K
KN
NE
EK
KT
T*
*
Default setting: L
LA
AS
ST
T U
US
SE
ED
D
KNEKT
If your EXOTIK is installed in a Linn KNEKT multi-room system, select the appropriate
setting. If your EXOTIK is not installed in a KNEKT system, select N
NO
ON
NE
E.
Options: N
NO
ON
NE
E,, M
MA
AIIN
N R
RO
OO
OM
M,, L
LO
OC
CA
AL
L R
RO
OO
OM
M,, IIN
NT
TE
ER
RS
SE
EK
KT
T
Default setting: N
NO
ON
NE
E
ACCESSORY SOCKET
Define the use of the accessory (ACC/RCU) socket on the back panel.
Options: R
RC
CU
U*
* (KNEKT Room Control Unit),, IIR
R (Infrared Repeater)
Default setting: R
RC
CU
U
*For use with Linn KNEKT systems.
PRODUCT IR
Enable or disable the infrared receiver on the front of the unit.
Options: E
EN
NA
AB
BL
LE
E,, D
DIIS
SA
AB
BL
LE
E
Default setting: E
EN
NA
AB
BL
LE
E
RS232 Setup
Accesses the RS232 SETUP sub-menu.
The RS232 Setup sub-menu is for use if the EXOTIK is communicating with other RS232
enabled products (e.g. a third-party controller).
BAUD RATE
Set the baud rate to suit the RS232 protocol being used.
Range: 112
20
00
0 tto
o 2
23
30
04
40
00
0 (11 settings)
Default setting: 9
96
60
00
0
PARITY
Set parity to suit the RS232 protocol being used.
Options: E
EV
VE
EN
N,, O
OD
DD
D
Default setting: E
EV
VE
EN
N
DATA BITS
Set the data bits to suit the RS232 protocol being used.
Options: 7
7,, 8
8
Default setting: 7
7
STOP BITS
Set the stop bits to suit the RS232 protocol being used.
Options: 11,, 2
2
Default setting: 11
13
English
EXOTIK PRE-AMPLIFIER
Owner’s Manual