Kenwood KPA-SD100 - Manual (Page 3)

English
-3
Operation
7
Vehicle’s display setup
1. Select "EXT.ACC.CONT/ACC.CONT/EXT.ACC Control" from the
Centre Unit menu items.
This does not work during reception of MW / LW broadcasts(if the centre unit
displays the sensors, it is displayed as "- - - -").
2. Hold down the
4 or ¢ button for more than two seconds.
Centre Unit enters display-switching mode.
3. The display changes as follows when you press the
4 button or ¢ button.
Display switching:
O Sensor*
2 /Compass* 3
O Music Source O
• * 2 : Sensor display appears when the Sensor Box (KPA-SS100) is connected.
• * 3 : Compass display appears when the Compass Unit (KPA-CP100) is connected.
• In Music Source display, the number of items switched, such as source display and track display, varies with the source
currently being played.
• The time reading on the vehicle’s display and time reading on the centre unit display are not synchronized.
7
Compass setup (When the KPA-CP100 is connected)
By combining this unit with the KPA-CP100 (sold separately), the compass display can be
shown on the display screen.
1. Select "Sensor CONT/SENS.CONT/Sensor Control" from the Centre Unit menu items.
This does not work during reception of MW / LW broadcasts .
2. Hold down the
4 or ¢ button for more than
two seconds.
The Centre Unit enters Compass setup mode.
3. Press the FM or AM button.
Each pressing toggles setup mode as follows:
O Direction step switching O Compass
direction compensation
O Target direction setup
O
During the Compass setup procedure, the message "SENS.CNT" will be displayed on the vehicle’s display screen.
4. At the item you want to set up, press the
4 or ¢ button.
Each item allows you to set the following:
Direction step switching:
Toggle direction display modes.
O North direction (8 directions) mode O North direction (16 directions) mode O
Target direction (8 directions) mode
O Target direction (16 directions) modeO
North direction mode
The vehicle's direction of travel will be displayed
with letters as one of the 8 or 16 compass
directions.
Target direction mode
In Target direction mode, you can set the desired
target direction, and any deviation from this
direction will then be displayed on the display .
(See "Target directions setup" for instructions on
setting the target direction.)
If it is displayed as "RIGHT 90.0/ R 90.0", the 90-degree
direction on the right is the direction of the destination.
NOTE
NOTE
NOTE
NOTE
NOTE
EJECT
PWR
OFF
MENU
DISP
NAME.S
SCAN RDM REP D.SCN M.RDM
DISC
DISC DAB
AUD
NF
AUTO AME
4 ¢
FM
AM MENU
Centre Unit
North directions
(8 directions)
North directions
(16 directions)
Target directions
(8 directions)
Target directions
(16 directions)
16-digit display
example(Centre Unit)
8-digit display
example(Centre Unit)
NORTH. DIR 8
NORTH. DIR 16
TARGET. DIR 16
TARGET. DIR 8
N. DIR 8
N. DIR 16
T. DIR 16
T. DIR 8
Display in adjustment mode
SENS.CNT
Vehicle’s
display
SENS.CNT
SENS.CNT
SENS.CNT
North direction display
(8 directions)
16-digit display example
8-digit display and
vehicle’s display example
DIRECTION W
DIRECTION SW
DIRECTION N
DIRECTION NNE
BACK 180.0
LEFT 112.5
FORWARD 0.0
RIGHT 90.0
DIR W
DIR SW
DIR N
DIR NNE
B 180.0
L 112.5
F 0.0
R 90.0
Compass display example
North direction display
(16 directions)
Target direction display
(16 directions)
Target direction display
(8 directions)