Kicker S10XSP - Manual (Page 2)

PERFORMANCE
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
2
INST
ALLA
TION
SOLOXSUBWOOFER
SPAIRASSEMBLY
Owner’sManual
S12XSP / S10XSP Models:
SOLOXSUBWOOFERSPAIRASSEMBLY 3
Authorized Kicker Dealer:
Purchase Date:
SPAIR Model Number:
_________________________
_________________________
_________________________
The Kicker SoloX subwoofers were specially designed for “Livin’ Loud” out in the harsh automotive
competition environment. When you push your subwoofers to the extreme, you're bound to find the
breaking point, and when you do you can be secure in knowing that Kicker has provided the SPAIR
(Simple Pull Apart Insertable Replacement) to replace all of the damaged elements of your Solo X
without a lengthy or difficult installation. You can simply remove your old SPAIR, unpack the new
SPAIR, reconnect the wires, drop it into the BAM (Basket and Motor Assembly) and screw it back on
to get your system back up and kicking in a matter of minutes.
Installation
1. To begin installation, start by removing the old SPAIR (Simple Pull Apart Insertable Replacement) from
the BAM (Basket and Motor Assembly) as shown below.
Remove the (8) eight acorn head 10-24 bolts
securing the old SPAIR to the BAM.
Install
Gap Cap
BAM
Locator Hole
Locator Pin
Old SPAIR
Disconnect
Speaker
Cable
Wires
Enclosure
Baffle
BAM
Disconnect the speaker wires from
the old SPAIR and take note of
how they were connected.
Remove the old SPAIR from the BAM and install
the supplied Gap Cap into the BAM around the
pole piece to protect the motor assembly from
debris during the installation.
a.
b.
c.
Acorn
Head
Bolts
Model:
Nominal Impedance [Zn], ohm (2 Ω model) [per coil]
Resonance Frequency [fs], Hz (2 Ω model)
Sensitivity [SPLo], dB @ 1W, 1m (2 Ω model)
Effective Piston Area [Sd], in 2 (m 2 )
Power Handling Watts, Peak (RMS)
Effective Excursion [EXmax ™], in (mm)
DC Resistance [Re], ohm (2 Ω model) [coils in series]
Voice Coil Inductance [Le], mH (2 Ω model)
Mechanical Q-Factor [Qms] (2 Ω model)
Electrical Q-Factor [Qes] (2 Ω model)
Total Q-Factor [Qts] (2 Ω model)
Force Factor [BL], Tm (2 Ω model)
Moving Mass [Mms], g (2 Ω model)
Equivalent Volume [Vas], ft 3 (2 Ω model)
Equivalent Volume [Vas], L (2 Ω model)
Net Displacement, in 3 (cc)
Mounting Depth, in (cm)
S12X4/2 Ω
4 (2)
37.8 (37.81)
87.80 (87.55)
106.8 (.0689)
5000 (2500)
.906 (23)
7.17 (4.09)
6.833 (4.654)
9.441 (10.076)
.550 (.458)
.520 (.438)
30.60 (27.6444)
302.6 (361)
1.3949 (1.1696)
39.50 (33.1245)
328.32 (5380)
8 9/16 (21.7)
S10X4/2 Ω
4 (2)
40.5 (36.237)
85.95 (85.65)
74.4 (.048)
5000 (2500)
.906 (23)
7.06 (3.99)
6.600 (5.512)
9.954 (10.266)
.497 (.393)
.474 (.379)
30.99 (26.7089)
265.8 (309)
.702 (.7216)
19 (20.4376)
311.04 (5100)
8 3/8 (21.3)
Performance
Figure 1
Old SPAIR
Enclosure
Baffle
Figure 2
Figure 3
Note: The use of a subsonic filter will significantly increase the power handling. The power handling specifications in these charts are
calculated using a 25Hz (68Hz for the Vented SPL enclosure), 24dB per octave sub-sonic (resonate frequency) filter.
A Note on PowerHandlingCapacity SoloX subwoofers will handle massive amounts of power in any of the
recommended enclosures, minimum or maximum. The smaller enclosures are best for use in limited-space
applications. The larger recommended enclosures will yield more bass at the resonate frequency of the enclosure.
The listed Power Handling capacities assume that both voice coils are in use with the appropriate sub-sonic/resonate
frequency filter. Always connect both coils in a dual voice-coil speaker.
SoloX Subwoofer and SPAIR - Covered by one or more of the following patents: U.S. Pat #'s 6,611,604, 6,731,773 D473,216, D456,386,
D449,293, D355,193; Taiwan Pat. #162,154; Other U.S. and foreign patents pending.