Kawasaki 840273 User Manual
Page 7

E
ED
DG
GE
E G
GR
RIIN
ND
DIIN
NG
G
D
Do
o n
no
ott u
ussee eed
dg
gee g
grriin
nd
diin
ng
g w
wh
heeeellss ffo
orr ccu
utt--o
offff w
wo
orrkk,, d
deeeep
p
g
grriin
nd
diin
ng
g o
orr ssu
ub
bjjeecctt tth
heem
m tto
o aan
nyy ssiid
dee p
prreessssu
urree aass tth
hiiss m
maayy lleeaad
d tto
o b
brreeaakkaag
gee
aan
nd
d p
po
ossssiib
bllee p
peerrsso
on
naall iin
njju
urryy.. These wheels should be used for shallow cutting
and notching (less than 1/2" in depth). Keep the open side of the guard away
from the operator at all times.
Edge grinding should only be done with wheels specifically designed for this purpose.
R
RE
EM
MO
OV
VIIN
NG
G G
GU
UA
AR
RD
D FFO
OR
R S
SA
AN
ND
DIIN
NG
G O
OR
R U
US
SIIN
NG
G FFL
LA
AT
T W
WIIR
RE
E B
BR
RU
US
SH
HE
ES
S
• Set the Angle Grinder on a flat surface with the spindle facing up.
• Remove the inner and outer flanges, unscrew spring washer and remove
the guard.
• Store these parts carefully.
• Replace the guard after the job is finished.
A
AT
TT
TA
AC
CH
HIIN
NG
G S
SA
AN
ND
DIIN
NG
G D
DIIS
SC
C
• To remove the guard, see instructions
given in the “Removing Guard for
Sanding or Using Flat Wire Brushes”
Section above.
• Set the inner flange and outer flange on
the spindle.
• Push in the spindle lock button. Turn the
spindle until it locks into place.
• Once the spindle is locked, tighten the
sanding disc by hand.
O
OP
PE
ER
RA
AT
TIIN
NG
G T
TH
HE
E A
AN
NG
GL
LE
E G
GR
RIIN
ND
DE
ER
R
A
Allw
waayyss u
un
np
pllu
ug
g tth
hee tto
oo
oll b
beeffo
orree aatttteem
mp
pttiin
ng
g tto
o cch
haan
ng
gee tth
hee
g
gu
uaarrd
d o
orr aacccceesssso
orriieess..
WARNING
12
A
AT
TT
TA
AC
CH
HIIN
NG
G W
WH
HE
EE
EL
LS
S W
WIIT
TH
H D
DE
EP
PR
RE
ES
SS
SE
ED
D C
CE
EN
NT
TE
ER
RS
S
A
Allw
waayyss cch
heecckk tth
hee tto
oo
oll w
waarrn
niin
ng
g llaab
beell ffo
orr tth
hee rreecco
om
mm
meen
nd
d--
eed
d ssp
peeeed
d rraattiin
ng
g o
on
n aacccceesssso
orriieess.. Never run a wheel or brush over the rated
speed. Accessories exceeding the recommended speed may fly apart and cause
serious personal injury.
H
Hu
ub
bb
beed
d w
wh
heeeellss d
do
o n
no
ott rreeq
qu
uiirree m
mo
ou
un
nttiin
ng
g ffllaan
ng
geess..
• Press the spindle lock firm and
insure there is no movement in the
spindle. Then while the spindle lock
is depressed tighten the locking nut
in a clockwise direction using the
pin spanner.
• Allow the Angle Grinder to run in
idle for at least a minute with the
grinding or cutting disc correctly
assembled.
A
AT
TT
TA
AC
CH
HIIN
NG
G W
WIIR
RE
E B
BR
RU
US
SH
HE
ES
S
Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are
necessary.
WARNING
11
SPINDLE
LOCK
BUTTON
• Place the backing washer over the
spindle making sure the fit is tight.
• Place the grinding or cutting disc on the
top of the backing washer ensuring the
bore fits into the step of the flange.
• Mount the concave recess side of the
locking nut over the spindle.