Kenmore 665.1388 - Manual (Page 17)

17
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before opening the door. The Start/Resume
light will flash.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The Start/Resume light
will flash.
4. Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock (see Lock
On section in “Option Selections”), or the Start/Resume light will
continue to flash.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher runs the last full
wash cycle and options.
T URBO Z ONE ™ wash option
Select this option to activate the T URBO Z ONE ™ spray jets and
provide intensified water spray to the back of the lower dishrack.
The T
URBO Z ONE ™ wash option provides a concentrated wash
action to pans, casseroles, etc. with tough food soil.
This option may add heat and wash time to the cycle.
NOTE: T URBO Z ONE ™ is an option with the SMART WASH™,
Pots Pans, and Normal Wash cycles.
IMPORTANT:
■ Load pans, casserole dishes, etc. facing the T URBO Z ONE ™
spray jets in the back of the lower dishrack. Tip items toward
the rear of the dishrack to maximize coverage. Only one row
of items may face the T
URBO Z ONE ™ spray jets. Stacking,
overlapping, or nesting items will keep the T URBO Z ONE ™
spray jets from reaching all of the surfaces.
■ To maximize spray coverage, avoid placing silverware basket
or other items to interfere with the rotation of the
T
URBO Z ONE ™ spray jets.
■ Turn the T URBO Z ONE ™ wash option off if not loading items
for this option. Always use the Heavy Soil detergent fill
recommendation with T
URBO Z ONE ™ wash option. (See
“How much detergent to use” in “Detergent Dispenser”
section.)
Hi Temp
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp wash raises the water
temperature to 145ºF (63ºC), in the main wash. Heating the water
helps improve washing results. Hi Temp wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp wash is an option with the SMART WASH™,
Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH™, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dishload that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Fast
Wash and Quick Rinse.
Side view of T URBO Z ONE ™ wash area