Kawasaki RH1-090048 - Manual (Page 34)

C CH HA AR RG GIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
C CH HA AR RG GE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Plug the charger into
the nearest 120 volt
electrical outlet.
2. Make sure the trigger
on the Cordless Drill
is in the ““O
OFFFF””
position and remove
the battery pack from
the Cordless Drill.
3. Insert the battery pack into
the charger. Be sure that the
battery pack is fully seated
in the charger.
Do not force.
4. The red indicator light should come ““O ON N”” indicating that the battery pack is in
a “Fast Charge” mode. If the green indicator light comes ““O ON N””, then the battery
is already fully charged.
5. After approximately one hour of charging, the red indicator light should go
““O OFFFF”” and the green light should come ““O ON N”” indicating that the battery is fully
charged and the charger is now in a “Trickle Charge” mode.
6. The battery can be left in a “Trickle Charge” mode until ready to use.
IIM MP PO OR RT TA AN NT T IIN NFFO OR RM MA AT TIIO ON N FFO OR R R RE EC CH HA AR RG GIIN NG G H HO OT T B BA AT TT TE ER RIIE ES S
When using your Cordless Drill continuously, the batteries in your battery pack
will become hot. You should let a hot battery pack cool down for approximately
30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery
pack cools down, the red light will glow continuously to indicate fast charging
mode, 1-hour charge time.
T Th hiiss w wiillll o occccu urr w wh heen n cco on nttiin nu uo ou uss u ussee o off yyo ou urr C Co orrd dlleessss
D Drriillll ccaau usseess tth hee b baatttteerryy p paacckk tto o b beecco om mee h ho ott.. It does not occur under normal
circumstances.
14
R RE EM MO OV VIIN NG G // A AT TT TA AC CH HIIN NG G B BA AT TT TE ER RY Y P PA AC CK K
R RE EM MO OV VE E B BA AT TT TE ER RY Y P PA AC CK K::
1. Press both release
buttons on either
side of the Cordless
Circular Saw to release the
battery pack.
2. Pull battery pack free of
Cordless Circular Saw.
A AT TT TA AC CH H B BA AT TT TE ER RY Y P PA AC CK K::
1. Align the raised portion of
the battery pack with the
groove in the
battery compartment of
the Cordless Circular Saw.
2. Press the battery pack into
place. Make sure the latch-
es are securely fastened. Do not use the Cordless Circular Saw if the battery
pack is not seated properly.
C CH HA AR RG GE ER R
B Beeffo orree u ussiin ng g b baatttteerryy cch haarrg geerr,, p plleeaassee rreeaad d ccaarreeffu ullllyy aallll
iin nssttrru uccttiio on nss aan nd d ccaau uttiio on naarryy m maarrkkiin ng gss o on n b baatttteerryy cch haarrg geerr,, b baatttteerryy p paacckk aan nd d
p prro od du ucctt u ussiin ng g b baatttteerryy..
U Ussee o on nllyy tth hee cch haarrg geerr w wh hiicch h aacccco om mp paan niieed d yyo ou urr p prro od du ucctt o orr d diirreecctt rreep pllaacceem meen ntt aass
lliisstteed d iin n tth hiiss m maan nu uaall.. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
D Do o n no ott d diissaasssseem mb bllee cch haarrg geerr..
D Do o n no ott u ussee cch haarrg geerr iiff iitt h haass b beeeen n d daam maag geed d,, lleefftt o ou uttd do oo orrss iin n tth hee rraaiin n,, ssn no ow w,, w weett
o orr d daam mp p een nvviirro on nm meen nttss,, o orr iim mm meerrsseed d iin n lliiq qu uiid d..
T Th hee b baatttteerryy p paacckk aan nd d cch haarrg geerr h heeaatt d du urriin ng g cch haarrg giin ng g.. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
W Wh heen n tth hee b baatttteerryy p paacckk rreeq qu uiirreess rreecch haarrg giin ng g,, aa 1 1 h ho ou urr cch haarrg gee aallllo ow wss tth hee tto oo oll tto o
o op peerraattee aatt ffu ullll p po ow weerr.. A charging indicator light on the charger will illuminate to
show that charging is taking place.
13
RELEASE
BUTTON
BATTERY PACK
LED
LIGHT
BATTERY
CHARGER