Sharp CD-DH950P - Manual (Page 13)

E-12
Timer and sleep operation (Remote control only) (continued)
1 minute or more
Once timer Daily timer
Start Stop Start Stop
Timer playback Q
Before setting timer:
Check that the clock is set to the correct time. If it is 1
not set, you cannot use the timer function.
For timer playback: Plug in USB, dock iPod/iPhone,
2
load discs or tape to be played.
Press the ON/STAND-BY button to turn the power on. 1
Press and hold the CLOCK/TIMER button. 2
Within 10 seconds, press the 3 or button
to select “ONCE” or “DAILY”, and press the MEMORY
button. Set the clock to the correct time if “ONCE” or
“DAILY” does not appear.
Within 10 seconds, press the
4 or button to select
“ONCE SET” or “DAILY SET”, and press the MEMORY
button.
To adjust the hour, press the
5 or button and then
press the MEMORY button.
To adjust the minutes, press the
6 or button and
then press the MEMORY button.
Set the time to fi nish as in steps 5 and 6 above.
7
To select the timer playback source (CD, TUNER, USB, 8
iPhone/iPod, TAPE or AUDIO IN), press the or
button. Press the MEMORY button.
When you select the tuner, select a station by pressing
the
or button, and then press the MEMORY
button. If a station has not been programmed, “NO
PRESET” will be displayed and timer setting will be
canceled.
Adjust the volume using the VOLUME control, and then
9
press the MEMORY button. Do not turn the volume up
too high.
Press the ON/STAND-BY button to enter the power
10
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
1 2 3 4 5
4
5
3
2
1
MINI COMPONENT SYSTEM
OPEN / CLOSE
TUNING PRESET
USB AUDIO IN
TAPE
TUNER
CD
TIMER
iPod/iPhone
POWER ON/ STAND-BY
(BAND)
VOL. VOL.
REMOTE
SENSOR CD-DH950P
When the preset time is reached, playback will start. 11
The volume will increase gradually until it reaches the
preset volume. The “
” or “DAILY” indicator will blink
during timer playback.
When the timer end time is reached, the system will
12
enter the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer operates at the same time every day. It
will continue until the daily timer setting is canceled.
Cancel the daily timer when it is not in use.
Notes:
When performing timer playback using another unit O
connected to the USB terminal or AUDIO IN jack,
select “USB” or “AUDIO IN” in step 8.
This unit will turn on or enter the power stand-by mode
O
automatically. However, the connected unit will not
turn on or off. To stop the timer playback, follow step
“Canceling the timer setting” of this page.
Checking the timer setting:
Turn the power on and press and hold down the 1
CLOCK/TIMER button.
Within 10 seconds, press the
2 or button to select
“ONCE” or “DAILY”, and press the MEMORY button.
Within 10 seconds, press the
3 or button to
select “ONCE CALL” or “DAILY CALL”, and press the
MEMORY button.
Canceling the timer setting:
Turn the power on and press and hold down the 1
CLOCK/TIMER button.
Within 10 seconds, press the
2 or button to select
“ONCE” or “DAILY”, and press the MEMORY button.
Within 10 seconds, press the
3 or button to select
“ONCE OFF” or “DAILY OFF”, and press the MEMORY
button. Timer will be canceled (the setting will not be
canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To
reuse the same setting, perform the following operations.
Turn the power on and press and hold down the 1
CLOCK/TIMER button.
Within 10 seconds, press the
2 or button to select
“ONCE” or “DAILY”, and press the MEMORY button.
Within 10 seconds, press the
3 or button to select
“ONCE ON” or “DAILY ON”, and press the MEMORY
button.
Press the ON/STAND-BY button to enter the power
4
stand-by mode.
Sleep operation Q
The iPod, Audio In, radio, CD, MP3/WMA disc, USB and
cassette tape can all be turned off automatically.
Play back the desired sound source. 1
Press the SLEEP button. 2
Within 10 seconds, press the SLEEP button repeatedly 3
to select the time and then press the MEMORY
button.
10 20 30 ....... 80 90
“SLEEP” will appear. 4
The unit will enter the power stand-by mode 5
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation fi nishes.
To confi rm the remaining sleep time:
While “SLEEP” is indicated, press the SLEEP button. 1
To cancel the sleep operation:
Press the ON/STAND-BY button while “SLEEP” is
indicated. To cancel the sleep operation without setting the
unit to the stand-by mode, proceed as follows.
While “SLEEP” is indicated, press the SLEEP button. 1
Within 10 seconds, press the SLEEP button repeatedly 2
to select “SLEEP OFF” and then press the MEMORY
button.
CD-DH950P_US_EN.indd 12 CD-DH950P_US_EN.indd 12 2/21/2011 12:13:25 PM 2/21/2011 12:13:25 PM