Symphonic RSMWD2205 - Manual (Page 27)

– 27 – EN
Quick Use Guide
✄
Please refer to “Basic TV
Connection” on the front page
before you use this unit.
RF Output Channel
If channel 3 is already occupied for
broadcasting,
1)Set your TV to channel 4.
2)Insert a pre-recorded tape into this
unit.
3)Hit [SOURCE] on the unit so that the
VCR OUTPUT light is lit.
• If “VCR” light does not appear on the
display of this unit, hit [VCR/TV] on
the remote control.
4)Hit [PLAY B] once.
5)After a few seconds, hit [PLAY B]
on the unit for 3 seconds.
• The RF output channel will change
to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on
the TV screen, repeat step 4).
6)Hit [STOP C] to stop playback.
Connections 1 Clock Set Up 5
VCR/DVD Switching 3
Installing the Batteries
for the Remote Control 2
Turn on the unit for the
first time 4
2 3 1
A
G H
Y X
y
AUDIO VIDEO REW F.FWD STOP/EJECT RECORD IR
REC TIMER B B C C A D E
CHANNEL
OPEN/
CLOSE
SOURCE
X Y VCR DVD DISC IN PLAY
PREV NEXT STANDBY-ON PLAY STOP PLAY
X Y
VCR DVD
SOURCE PREV
SOURCE button
DVD OUTPUT
light
VCR OUTPUT
light
DVD button
VCR button
STANDBY-ON
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
RECORD
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE T-SET ANGLE
ENTER
RETURN
SEARCH MODE
REPEAT A-B
OPEN/CLOSE /EJECT SPEED AUDIO
CLEAR/ C. RESET
1 2 3
4 5 6
7 8 9
0 +10
Hit [VCR] on the remote control.
(Verify that the VCR OUTPUT light is lit.)
VCR MODE
Hit [DVD] on the remote control.
(Verify that the DVD OUTPUT light is lit.)
DVD MODE
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANÇAIS
ESPAÑOL
1 1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
3 3
CH 01
AUTO SET UP
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized
in this unit by using
[SKIP/CH. G
G /K K H H /L L ]
(or [CHANNEL K K /L L ]).
• If “AUTO SET UP” appears on the TV
screen again, check the cable connections.
Then, hit [B] once again.
Y Y es es Hit MENU to
exit.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
NO
TV Screen Remote Control
VCR VCR
VCR
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
Select the current day.
• If the clock is not set, the
CLOCK SET screen
appears when you hit
[MENU]. In this case, go
to step 2).
VCR VCR
VCR
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select the current year.
Select “AM” or “PM”.
8 8 To exit the CLOCK SET
screen
Select the current hour.
Select the current minute.
2 2
3 3
4 4
5 5
6 6
7 7
Hint Hint
• Hitting only [SOURCE] on the front panel
DOES NOT switch the mode of the
remote control. You MUST select the cor-
rect mode on the remote control.
or
STANBY-ON
MENU
or
or
or
or
or
or
or
✄
H98K0UD_EN/SP.qx3 04.12.20 13:23 Page 27