Stanton C.502 - Manual (Page 12)

11
12. Fader start
You have the possibility to start the respective CD player directly from the mixer. Make sure that the Control
socket is connected with the respective socket on the mixer. Additionally, the Audio out sockets have to be
connected with the Line input sockets of your mixer. Please note that the Fader start function only works
with the appropriate mixers. Insert the CD and select the desired track. Start playback from your mixer.
13. Relay
In the Relay operation, the device automatically switches to the other player after every track. In this way,
you have the possibility to enlarge the music program by using several CDs.
CAUTION: The Relay operation does not work properly if the two CD players are connected to different power
amplifiers.
To start, press the Relay button. Press the Single button (the display shows “ SINGLE” ) on both CD players.
Start playback of CD1. As soon as the current track of CD1 is finished, the player automatically starts CD2.
The first CD player goes into Pause-mode. Press the single button again for continuous mode (the “SINGLE”
display is not lit). When playback of all tracks of CD1 is finished, the player automatically starts CD2 and Cd1
is goes into pause-mode.
You can load a new CD or memorize a Cue point for either player in the Pause Mode.
When playback of all tracks or the current track of CD2 is finished, the player automatically starts CD1 and
CD2 goes into pause-mode.
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord.
If it is damaged or deformed, it may cause electric
shock or malfunction when used. When removing
from wall outlet,be sure to remove by holding the
plug attachment and not by pulling the cord.
2. In order to prevent electric shock, do not open the
top cover. If a problem occurs, contact your dealer.
3. Do not place metal objects or spill liquid inside the
CD player. Electric shock or malfunction may result.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
TO PREVENT ELECTRIC SHOCK DO NOT USE
THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
IMPORTANT TO SAFETY NOTE:
This CD player uses the semiconductor laser. To allow
you to enjoy music at a stable operation, it is recommended
to use this in a room of 5ºC 41ºF - 35ºC 95ºF.
CAUTION:
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. ___________ Serial No. ___________
CAUTION: TO REDUCE THE
RISK OF ELECTRICf SHOCK,
DO NOT REMOVE THE COVER
(OR BACK) . THERE ARE NO
SERVICEABLE PARTS INSIDE.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
insulated "dangerous voltage" within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
FOR U.S.A. & CANADA MODEL ONLY
CAUTION
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
REFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
DOUBLE INSULATED - WHEN SERVICING, USE
ONLY IDENTICAL REPLACEMENT PARTS.
NOTE:
This unit may cause interference to radio and television
reception.
Line Voltage Selection (for multiple voltage
model only)
The desired voltage may be set with the
VOLTAGE SELECTOR switch on the rear
panel, using a screwdriver.
Do not twist the VOLTAGE SELECTOR
switch with excessive force as this may
cause damage
If the VOLTAGE SELECTOR switch does not move
smoothly, please contact a qualified serviceman.
1
RATING LABEL
CLASS 1 LABEL
115V
230V