Sharp PN-E802 - Manual (Page 36)

36
E
AUDIO menu
Function Command Direction Parameter Reply Control/Response contents *1
*2
(A) (B)
TREBLE AUTR WR -5-5 -5-5
○ ○ ○ BASS AUBS WR -5-5 -5-5
BALANCE AUBL WR -10-10 -10-10
RESET ARST W 3 -
SETUP menu
Function Command Direction Parameter Reply Control/Response contents *1
*2
(A) (B)
OSD H-POSITION OSDH WR 0-100 0-100
○
○ ○
OSD V-POSITION OSDV WR 0-100 0-100
SCREEN MOTION SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4 ○
MOTION TIME 1 MTIM WR 0-20 0-20
○
MOTION TIME 2 PATTERN1 MINT WR 10-990 10-990 Per 10 seconds
○
PATTERN2-4 MINT WR 5-20 5-20 Per second
MONITOR STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT
○
MONAURAL AUDIO MONO WR 0-1 0-1 0: OFF, 1: ON ○
LANGUAGE LANG WR 14 14 ENGLISH
○
1 1 DEUTSCH
2 2 FRANÇAIS
3 3 ITALIANO
4 4 ESPAÑOL
5 5 РУССКИЙ
6 6
POWER ON DELAY PWOD WR 0 0 OFF
○
1-60 1-60 ON
STANDBY MODE STBM WR 0-1 0-1 0: STANDARD, 1: LOW POWER
(“ERR" when SCHEDULE is effective or OFF is selected for LED.)
○
OFF IF NO OPERATION ATOF WR 0-1 0-1 0: OFF, 1: ON ○
HOT PLUG CONTROL (DVI) HPCT WR 0-1 0-1 0: OFF, 1: ON ○ - ○
HOT PLUG CONTROL (HDMI) HPCH WR 0-1 0-1 0: OFF, 1: ON
○ ○ ○
RS-232C/LAN SELECT CTLS WR 0-1 0-1 0 : RS-232C 1 : LAN ○ - ○
ID NUMBER ID NO. SETTING IDST W 0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)
○ ○ ○
R 0-255 Returns the monitor’s ID number.
ID NO. SETTING
(ONCE)
IDSL W 1-255 Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0 Clears the ID number if one has been designated.
ID NO. SETTING
(SUBSEQUENT)
IDLK W 1-255 Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands
after this command.
0 Clears the ID number if one has been designated.
ID CHECK IDCK W 0 ID : xxx
IDLK : yyy
Displays monitor’s own ID number and the selected ID number on the
screen.
ID DISPLAY IDDP W 0-2 0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)
(When the PN-ZB01 is attached, the IP address and MAC address are
both displayed.)
BAUD RATE BAUD WR 0-2 0-2 0: 9600bps, 1: 19200bps, 2: 38400bps
○ ○ ○
SPEAKER SELECT SPSL WR 0-1 0-1 0: Internal speaker, 1: External speaker ○ - ○
HDMI AUTO VIEW HDAW WR 0-1 0-1 0: OFF, 1: ON
○ ○ ○
SETTING COPY MODE CPMD WR 0 0 Copy to all monitors.
○ ○ ○
1-225 1-225 Copy to the monitor with the set ID Number.
SETTING COPY TARGET CPTG WR 0 0 Copies the PICTURE menu settings.
1 1 Copies all the settings.
LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON
Controlling the Monitor with a PC (RS-232C)