Superior Standard Series Unvented Decorative Gas Fireplaces VFPF-CMN-2 - Manual (Page 12)

NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 12
Optional on Unit Rocker Switch
An optional rocker switch kit can be installed
directly on all VFST series appliances to provide
for On and Off operation in lieu of a wall switch.
This kit is designed to install in the lower control
compartment out of view and is perfect for use
in high volume areas such as lobbies and model
homes where limited access to the appliance
On/Off switch is desirable. This kit can be
retrofitted to previously installed appliances
and may be temporarily installed in place of
other switch circuitry.
Gas Flex Line with Valve
A gas flex line kit is available to aid in attaching
the appliance to the gas supply. This kit can
only be used where local codes permit. The kit
includes a
¹⁄₂" NPT to ³⁄₈" flare in line shut-off
valve, a 12" flex line ³⁄₈" female flare through and
a ³⁄₈" flare to ³⁄₈" NPT fitting. The components of
this kit are rated for both natural and propane
gas. This kit is designed to be used as an aid in
installing the appliance.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERATURES. USE
CAUTION AROUND THE APPLIANCE TO
AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE SUPER-
VISED WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
Solid Brass Hood Kit
An attractive solid brass hood kit is available
for use with these VF appliances. The brass
hood kit is designed to be fitted to your appli-
ance above the door. In addition to providing
an aesthetically pleasing appearance to your
appliance installation, the hood reduces heat
effects to decorative mantles and finish mate-
rials located directly above the fireplace open-
ing. The hood kit includes the necessary
attaching hardware. This kit can be retrofitted
to previously installed appliances.
Solid Brass Louver Kit
Solid brass louvers are available for use with
these appliances. These louvers are designed
to replace the standard black louvers that are
provided with the appliance. The brass louver
kit includes three (3) louvers that simply snap
into place. They provide a touch of elegance to
the VF appliance. This kit can be retrofitted to
previously installed appliances.
Decorative Volcanic Stone
The decorative volcanic stone, Model DVS, can
be used to enhance the look of your appliance.
Spread the decorative volcanic stone evenly
around the bottom of the firebox.
Wall Thermostat Kit
A wall thermostat kit is available for use with
these appliances. The wall thermostat is de-
signed to be wired directly to the appliance
millivolt gas control circuit and provide auto-
matic On/Off control of the appliance to main-
tain a desired temperature within the room.
Solid Brass Hood Kit
An attractive solid brass hood kit is available
for use with these VF appliances. The brass
hood kit is designed to be fitted to your appli-
ance above the door. In addition to providing
an aesthetically pleasing appearance to your
appliance installation, the hood reduces heat
effects to decorative mantles and finish mate-
rials located directly above the fireplace open-
ing. The hood kit includes the necessary
attaching hardware. This kit can be retrofitted
to previously installed appliances.
Glass Door Kit
The VF6BDK Glass Door can be installed in
pairs on the appliance in place of the standard
screen panels. The glass doors add beauty and
protection for your appliance. Glass doors
prevent cross drafts that may cause unwanted
flame impingement on the logs.
Square Trim Kit
A square trim kit is available for the VFST
Series. This kit is easy to install and does not
require hardware to attach it as designed, di-
rectly to the standard door frame. The four
piece square trim kit can be installed without
the bottom or bottom and side pieces to cus-
tomize the look of our appliance. This kit can be
retrofitted to previously installed appliances.
Brass Square Surround Kit
A decorative brass square surround kit is avail-
able for use with these appliances. The BSK-6 is
designed to attach directly to the front face of the
appliance at its extreme edges. The BSK-6
provides a picture frame finish for the appliance
2
¹⁄₂" wide. The brass square surround kit can be
retrofitted onto previously installed appliances.
Screen Panel Kit
An optional screen panel can be installed on the
VFST door. This screen panel is easy to install
using the provided hardware. The screen panel
can be installed with both ceramic and tempered
glass in the door. This kit can be retrofitted to
previously installed VFST appliances.The screen
panel kit can not be used in conjunction with
either of the decorative arch kits.
Decorative Arch Kits
Two arch kits are available for the VFST Series.
A one-piece complete door arch kit and a four-
piece arch frame kit. Both kits are easy to install
and do not require hardware to attach them to
the standard door frame. The four-piece arch
frame kit can be installed without the bottom or
bottom and side pieces to customize the look of
your appliance. These kits can be retrofitted to
previously installed VFST Series appliances.
The decorative arch kits can not be used in
conjunction with the screen panel kit.