Samson Mixer S62 - Manual (Page 2)

ARCHITECT’S & ENGINEER’S
SPECIFICATION
The mixer amplifier shall incorporate a 150 W
monophonic amplifier, a 5-band graphic equalizer and a
monophonic mixer with 6 microphone/line-input chan-
nels. Microphone inputs shall be on XLR-type connec-
tors and line inputs shall be on balanced 1/4
″
Tip-Ring-
Sleeve phone connectors. An independent line-level
CD/tape input (routed to channel 6) shall be on phono
connectors. Each channel shall have an aux/reverb send,
2-band equalization and a level control.
The mixer shall provide an effects output on a 1/4
″
phone connector, as well as a preamp out and power
amp in for submix applications on 1/4
″
phone connec-
tors. An effects return shall be provided on a 1/4
′′
phone
connector, and it shall have an independent level con-
trol. Phantom Power of +48 V shall be provided for
operation of condenser microphones. The amplifier shall
be passively cooled. Amplifier output shall be provided
on two 1/4
″
phone connectors. Indicators shall be pro-
vided for peak level (3 dB before clipping), power and
amplifier protection. The unit shall be of a rack-mount
type.
The amplifier shall deliver maximum power equal
to or greater than 150 W into 4 ohms, signal-to-noise
equal to or greater than 95 dB, THD less than 0.1% and
frequency response of ±3 dB from 20 Hz to 50 kHz. The
mixer shall have residual noise of 70 dBu, signal-to-noise
equal to or greater than 70 dB and THD less than 0.03%.
Total power consumed at 1/8 audio power shall be 134
W (115 Vac). Dimensions shall be 19
″
(480 mm) wide,
9
″
(230 mm) deep and 3.5
″
(88 mm; 2 rack spaces)
high. Weight shall be 17.6 lb. (8 kg). The mixer amplifier
shall carry a three-year warranty.
The mixer amplifier shall be a SAMSON S62.
1
2 3
1
2 3
2
3
1
T
R
S
2
3
1
T
R
S
T
S TN
T
S TN
AUX SEND
REVERB
PEAK
PRE-OUT
MAIN
AMP IN
A
B
150 Wrms
Power Amp
A UX/REV MAIN
HIGH
AUX/REV
TAPE/CD L
TAPE/CD R
MIC PRE
MIC INPUT
LINE INPUT
PAD
(LINE)
LOW
AUX EFFECT RETURN
AUX/REV
-10db
HIGH
LEVEL
AUX.EFFECT
MIC PRE
MIC INPUT
LINE INPUT
PAD
(LINE)
AUX/REV
LOW
-10db
LEVEL
+/-15db
(INV)
TAPE IN CH6
A UX/REV MAIN +36
MAIN
+/-15db
+/-15db
(INV)
PEAK
DETECTOR
2 INPUT
CHANNELS 1-5
AUX
RETURN
CHANNEL 6
REVERB
5 BAND
GRAPHIC EQ
EQ 2 BAND
EQ 2 BAND
S62 SPECIFICATIONS
MIXER/PREAMP SECTION
Total harmonic distortion (with 30 kHz LPF):
Mic in to preamp out: < 0.05%
Line in to preamp out: < 0.03%
Aux return to preamp out: < 0.03%
Signal to noise ratio (with 30 kHz LPF, unity gain):
Mic input (-50 dBu): 67 dB
Line input (-10 dBu): 70 dB
Maximum voltage gain (1 kHz):
Mic in to preamp out: 54 dB
Line in to preamp out: 24 dB
Tape in to preamp out: 24 dB
Aux return to preamp out: 10 dB
Residual noise (with 30 kHz LPF, VR min):
Preamp out: 70 dBu
Tone controls:
High (10 kHz): ± 15 dB
Low (100 Hz): ± 15 dB
Graphic equalizer (30, 120, 480 Hz, 2, 8 kHz): ± 15 dB
Peak LED: 3 dB before clipping
Tape input sensitivity (-10 dB): 300 mV
Crosstalk (1 kHz, EQ flat):
Ch vs. Ch: 76 dB
Input vs. output: 78 dB
POWER AMP SECTION
Rated output power (1 kHz):
150 W into 4
Ω
Total harmonic distortion (with 30 kHz LPF): < 0.1%
Signal to noise ratio (with 30 kHz LPF): 95 dB
Frequency response (±3 dB): 20 Hz - 50 kHz
Maximum voltage gain (1 kHz): 36 dB
Residual noise (VR min): 70 dB typical
Idle current (across the 0.47
Ω
emitter resistor): < 20 mA
DC offset voltage: 0 ± 50 mV
GENERAL
Dimensions:
19
″
(w) x 9
″
(d) x 3.5
″
(h)
480 mm (w) x 230 mm (d) x 88 mm (h)
Weight: 17.6 lb. / 8 kg.
Power requirements: 115 Vac • 50/60 Hz
Power consumption (1/8 power): 134 W (115 Vac)
Specifications subject to change without notice. © 1998 SAMSON