E-11, Setting the clock (remote control only), Timer and sleep operation (remote control only) – Sharp TINSZA625AWZZ User Manual
Page 12
09/11/03
CD-SW440N_EN.fm
E-11
In this example, the clock is set for the 12-hour (AM 12:00)
display.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The “CLOCK” will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK”
does not appear in step 2, step 3 (for selecting the 12-hour
or 24-hour display) will be skipped.
To change the 12-hour or 24-hour display:
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day.
For example, set the timer as a wake-up call every
morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program,
and use the daily timer to wake up.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
Press the
or
button to select 12-hour or
24-hour display and then press the MEMORY button.
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
4
To adjust the hour, press the
or
button and
then press the MEMORY button. Press the
or
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5
To adjust the minutes, press the
or
button
and then press the MEMORY button. Press the
or
button once to advance the time by 1 minute.
1
Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2
Perform “Setting the clock” from step 1 onwards.
Setting the clock (Remote control
only)
CD
USB
TAPE
“AM 12:00”
“AM 0:00”
“0:00”
Before setting timer:
●
Check that the clock is set to the correct time (refer to
page 11). If it is not set, you cannot use the timer
function.
●
For timer playback: Plug in USB or load disc/cassette
or dock iPod to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
or
button to
select “ONCE SET” or “DAILY SET”, and press the
MEMORY button. Set the clock to the correct time if
“ONCE SET” or “DAILY SET” does not appear.
4
Within 10 seconds, press the
or
button to
select “TIMER SET”, and press the MEMORY button.
5
To adjust the hour, press the
or
button and then
press the MEMORY button.
6
To adjust the minutes, press the
or
button and
then press the MEMORY button.
7
Set the time to finish as in steps 5 and 6 above.
8
To select the timer playback source (CD, TUNER, USB,
iPod, TAPE or AUDIO IN), press the
or
button.
Press the MEMORY button.
When you select the tuner, select a station by pressing
the
or
button, and then press the MEMORY
button. If a station has not been programmed, “NO
PRESET” will be displayed and timer setting will be
canceled.
9
Adjust the volume using the VOLUME control, and then
press the MEMORY button. Do not turn the volume up
too high.
10
Press the ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
Timer and sleep operation (Remote
control only)
Once timer
Daily timer
Start
Stop
1 minute or more
Start
Stop
Timer playback