Samsung CLX-3170FN - Manual (Page 30)

30 _Getting started
Configuring wireless network from syncthru web
service
You must configure the appropriate network parameters to use your printer
in a wireless network. You can use SyncThru™ Web Service, an embedded
web site of your printer. This section gives you basic information on
802.11b/g network parameters which can be configured from the
SyncThru™ Web Service.
You can configure basic wireless settings, such as SSID, Operation Mode
and WPA Shared Key. You can retrieve basic settings by selecting a
wireless network.
Wizard mode
1. Prior to wireless network settings, you should set IP address for the
machine first. See "Using the SetIP program" on page 27.
2. Enter your machine’s IP address as the URL in a browser and click Go
to access the web site of your machine.
3. Click Network Settings and Wireless.
4. Select Wizard in Wireless Settings.
5. Click Next.
6. Select Network Name(SSID) in SSID Setup.
• SSID: SSID(Service Set Identifier) is a name that identifies a wireless
network. Access points and wireless devices attempting to connect
to a specific wireless network must use the same SSID. The SSID is
case-sensitive.
• Operation Mode: Operation Mode refers to the type of wireless
connections.
- Ad-hoc: allows wireless devices to communicate directly with each
other in a peer-to-peer environment.
- Infrastructure: allows wireless devices to communicate with each
other through an access point.
7. Click Next.
If wireless security setting window appears, enter the registered
password and click Next.
•
Operation Mode is Infrastructure:
- None: This is used when the validation of a wireless device’s
identity and data encryption are not required for your network. Open
system is used for IEEE 802.11 authentication.
- Static WEP: This uses the WEP (Wired Equivalent Privacy)
algorithm suggested by IEEE 802.11 standard for security. Static
WEP security mode requires a proper WEP key for data encryption,
decryption, and IEEE 802.11 authentication.
- WPA Personal: You can select WPA-PSK to authenticate the print
server based on WPA Pre-Shared Key. This uses a shared secret
key (generally called Pre Shared Key passphrase) that is manually
configured on the access point and each of its clients. This is
suitable for users who want to use WPA but do not have a RADIUS
server installed on their network.
• Operation Mode is Ad-hoc:
- None: This is used when the validation of a wireless device’s
identity and data encryption are not required for your network. Open
system is used for IEEE 802.11 authentication.
- Static WEP: This uses the WEP (Wired Equivalent Privacy)
algorithm suggested by IEEE 802.11 standard for security. Static
WEP security mode requires a proper WEP key for data encryption,
decryption, and IEEE 802.11 authentication.
8. Wizard Setup Confirmation window appears, please check your
wireless setup. If the setup is right, click Apply.
9. Click OK.
Custom mode
1. Enter your machine’s IP address as the URL in a browser and click Go
to access the web site of your machine.
2. Click Network Settings and Wireless.
3. Select Custom in Wireless Settings.
4. Click Next.
5. Select SSID in Search List. If you cannot find SSID you want, click
Refresh, or Enter SSID you want after selecting Insert New SSID.
6. Select Operation Mode from the drop-down list.
If you select Ad-hoc in Operation Mode, select Ad-hoc Channel. If you
select Auto Setting, the wireless network interface card on your machine
will automatically adjust the channels.
7. Select Authentication from the drop-down list.
8. Select Encryption from the drop-down list.
9. You might need to configure the Network Key Setup depending on the
set value of Network Setup or Security Setup.
10. Click Next.
11. Wireless Setup Confirmation window appears, please check your
wireless setup. If the setup is right, click Apply.
12. Click OK.
If you do not know about your wireless environment, please ask the
network administrator.
If Operation Mode of Network Name(SSID) is Infrastructure, you
must disconnect the network cable to activate wireless network
after completing the network setting.
If Operation Mode of Network Name(SSID) is Infrastructure, you
must disconnect the network cable to activate wireless network
after completing the network setting.