beautypg.com

Safety, Safety precautions precautions, Installation and use – Sanyo CE32LM5R User Manual

Page 2: Important: (uk only)

background image

2

SAFETY

SAFETY

PRECAUTIONS

PRECAUTIONS

GB

Do not allow anything to rest on the power
cord. Do not locate this LCD monitor where
the cord will be damaged by people walking
on it.

Do not overload wall outlets and extension
cords as this can result in fire or electric
shock.

A suitable socket outlet must be provided

near to the monitor and shall be easily accessible.
Do not place this LCD monitor near any heat sources such as
radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not place your LCD monitor on an unstable stand, shelf or
table. Serious injury to an individual, and damage to the LCD
monitor may result if it should fall. Your sales person can
recommend approved wall mounting kit. A special wall mounting
kit is available for this model.

This

LCD monitor

should be operated only from the type of power

source indicated on the monitor or as indicated in the Operating
Instructions. If you are not sure of the type of power supply, con-
sult your sales person or your local power company

For added protection it is strongly recommended that this

LCD

monitor

is supplied via an approved earth fault protection device.

WARNING:

To prevent injury the LCD monitor must be securely

attached to the wall in accordance with the manufacturers installa-
tion instructions.

IMPORTANT:

This product must be earthed

This unit is not disconnected from the mains unless the mains lead is
unplugged. The installer must make sure that the mains plug is easily
accessible.

Do not use immediately after moving the LCD monitor from a low
temperature to a high temperature environment, as this causes
condensation, which may result in fire, electric shock, or other
hazards. Before cleaning, unplug the monitor from the wall
socket.

Do not mount near an open flame source. Open flames must
never be used near this LCD monitor.
This LCD monitor should not be built in or enclosed in any way,
heat build up will reduce the life of the monitor.

This LCD monitor should have a minimum distance of 5cm away
from the wall and the monitor should have 10cm distance around
the top and sides.

Always mount using recommended and substantial fixtures and
fittings.
The rear finned section around the cabinet functions as a heat
sink, removing heat away from the monitor. The external surface
of the cabinet (finned area) must not be covered or the airflow
restricted in anyway by enclosing the LCD monitor.

Do not apply liquid cleaners or aerosol cleaners directly onto the
LCD monitor. Use a damp cloth for cleaning.

Installation and Use

CAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, but
improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the
following basic rules for its installation, use and servicing.

Important: (UK only)

THIS PRODUCT MUST BE EARTHED

This equipment is fitted with an approved mains lead and an
approved non rewireable UK mains plug. To change a fuse in this
type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or

BSI approved type.

3. Ensure that the fuse cover is correctly refitted.

If the fuse cover is lost or damaged the plug must NOT be used
but replaced with a serviceable plug.
If the fitted plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place. If the mains plug
contains a fuse, this should have a rating of 13 Amp, ensure the
fuse cover is correctly fitted. If a plug without a fuse is used, the
fuse at the distribution board should not be greater than 13 Amp.

Note:

The severed plug must be destroyed to avoid a possible

shock hazard should it be inserted into a 13 Amp socket elsewhere.

The wires in this mains lead are coloured in accordance with the
following code:

Blue ------->

Neutral

Brown ---->

Live

Green and Yellow ----> Earth

1. The Blue wire must be connected to the terminal which is

marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the

letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal

which is marked with the letter “E” or coloured GREEN or
GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding
type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS
THE MAINS LEAD IS UNPLUGGED.

THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS
EASILY ACCESSIBLE.

GB

10cm

10cm

10cm

5cm