SportDOG In-Ground Fence 100A - Manual (Page 7)

12 1-800-732-0144 SPORTDOG.COM 13
PREPARE THE COLLAR RECEIVER
Your Collar Receiver comes with short Contact Points installed. If your dog has a long or thick coat, you have two options to
ensure consistent contact: either trim the hair around the Contact Points or switch to the longer Contact Points included with
your system (follow 1-5 in diagram 5A). Tighten the Contact Points with pliers one-half turn beyond finger tight. Check the
tightness weekly.
TO INSERT AND REMOVE THE BATTERy
NOTE: Do not install the battery while the Collar Receiver is on your dog.
1. Remove the screws with a Philips screwdriver (5B).
2. Remove the Battery Lid (5B).
3. Install a 9-volt alkaline battery (5C).
4. Replace the Battery Lid (5C). Ensure o-ring stays in place.
5. Reinstall the screws. Do not over-tighten the screws.
Replacement 9-volt alkaline batteries can be found at many retailers.
5B 5C
3
3
2
A-67
4
1
2
5
5A
TO SET THE STIMULATION LEVEL
Read all steps before attempting to set the
Stimulation Level.
1. Remove the clear plastic cover with a coin to
expose the Stimulation Level Button (5D).
2. With the battery installed, press the Stimulation
Level Button and release when the Receiver
Indicator Light lights up (5E).
3. The Receiver Indicator Light will emit a series of
flashes representing the Stimulation Level. For
example, 2 flashes = Stimulation Level 2.
4. Increase the Stimulation Level by pressing and
releasing the Stimulation Level Button within 5
seconds of the previous series of flashes.
5. After setting the Stimulation Level, replace the
cover to protect the Stimulation Level Button.
5E 5D
The Stimulation Levels increase in strength from 1 to 5. Pushing the Stimulation Level Button while the Collar Receiver is on
level 5 will cause the Collar Receiver to go back to level 1. Refer to the Function and Response Table, on the following page,
to choose the Stimulation Level that best fits your dog.
The Collar Receiver is equipped to automatically increase the level of Stimulation the longer your dog remains in the
Stimulation Zone if the collar is set at level 2 or above.
The Receiver Indicator Light acts as a low battery indicator, flashing every 4 to 5 seconds when a replacement is required.
S
T
E
P
::
0
6
fUNCTION AND RESPONSE TABLE
Indicator Light
Response
Stimulation Level Collar Receiver Function Temperament of Dog
1 Flash 1 Beep and Vibrate (No Stimulation)
2 Flashes 2 Low Stimulation Timid
3 Flashes 3 Medium Stimulation Timid or Average
4 Flashes 4 Medium High Stimulation Average or Stubborn
5 Flashes 5 High Stimulation Stubborn
Flashes once every
4 to 5 seconds
Low Battery
NOTE: Begin training with Stimulation Level 2 and only increase if your dog does not respond to the Stimulation.
= Beep and Vibration Only + = Beep, Vibration and Stimulation = Stimulation Only
Important: The Stimulation Mode Switch (5f) can alter the response of the Collar
Receiver. When this Stimulation Mode Switch is set to “ ’’ or “
+
’’, the Collar
Receiver will respond according to the function and Response Table above. However, if the
Stimulation Mode Switch is set to “ ’’, this setting will override the Stimulation
Level 1 function. In this case, no Stimulation will be delivered, and the Collar Receiver will
NOT beep or vibrate; it will only make the ticking sound that normally indicates Stimulation.
We recommend to leave the Stimulation Mode Switch on the “ ’’ or “ +
’’
settings.
Range
Switch
Stimulation
Mode
Switch
5F
__________________________________________________
SET THE BOUNDARy WIDTH
AND TEST THE COLLAR RECEIVER
The Range Switch on the side of the Fence Transmitter has two settings. Set the Range
Switch to LOW if the amount of wire used for your property is less than 4,400 feet. Set the
Range Switch to HI if you used between 4,400 and 8,600 feet of wire.
Use the Range Adjuster knob to set the width of the Warning Zone and Stimulation Zone
(6A). Set the Boundary Width as wide as possible to give your dog the widest Warning and
Stimulation Zones without reducing the Boundary Area too much.
NOTE: The Range Adjuster knob does not change the Stimulation Level.
The Receiver Collar should NOT be on your dog when the system is tested.
Your dog may receive an unintended correction.
5
2 8
4
10
3
9 1
7
0
6
5
2 8
4
10
3
9 1
7
0
6
6A
To identify the Warning and Stimulation Zones, make sure the Collar Receiver’s battery is
properly installed, the Stimulation Level is set at 2 or above, and the Test Light contacts are
held to the Contact Points (6B). Walk toward the Boundary Wire holding the Collar Receiver at
your dog’s neck level (6C) until the Receiver Collar beeps (6D).
NOTE: The Collar Receiver is waterproof, which can make the beep hard to hear.
TEST TEST LIGHT LIGHT
6B
S
T
E
P
::
0
5
CAUTION
400-1178.indd 12-13 3/5/10 4:28 PM