Sanyo EM-842WS - Manual (Page 24)

B. B. B. B. B. REMOVING PRIMAR REMOVING PRIMAR REMOVING PRIMAR REMOVING PRIMAR REMOVING PRIMARY INTERLOCK SWITCH AND Y INTERLOCK SWITCH AND Y INTERLOCK SWITCH AND Y INTERLOCK SWITCH AND Y INTERLOCK SWITCH AND
INTERLOCK MONITOR SWITCH INTERLOCK MONITOR SWITCH INTERLOCK MONITOR SWITCH INTERLOCK MONITOR SWITCH INTERLOCK MONITOR SWITCH
(Figure 10-b)
(1) Disconnect all wire leads from Primary Interlock and
Interlock Monitor Switch.
(2) Pull the Primary Interlock Switch or Interlock Monitor
Switch upward at the same time while pushing the
Switch Stoppers to allow a space between the
switch body and catches.
(3) Make necessary adjustments or replacement of
switch by the reversing step (2) and check micro-
wave energy leakage according to “1. ADJUSTMENT
PROCEDURES” on page 1, after it is replaced with
new one, and check proper operation of it according
to “CHECKOUT PROCEDURE FOR SWITCHES” on
page 6.
Interlock Switch Replacement - when replacing
faulty switches, be sure switch mounting tabs are
not bent, broken or otherwise deficient in their
ability to secure the switches in place.
7 . 7 . 7 . 7 . 7 . DISASSEMBL DISASSEMBL DISASSEMBL DISASSEMBL DISASSEMBLY INSTRUCTIONS Y INSTRUCTIONS Y INSTRUCTIONS Y INSTRUCTIONS Y INSTRUCTIONS
••••• OVEN MUST BE DISCONNECTED FROM ELECTRICAL OVEN MUST BE DISCONNECTED FROM ELECTRICAL OVEN MUST BE DISCONNECTED FROM ELECTRICAL OVEN MUST BE DISCONNECTED FROM ELECTRICAL OVEN MUST BE DISCONNECTED FROM ELECTRICAL
OUTLET WHEN MAKING REPLACEMENTS, REP
OUTLET WHEN MAKING REPLACEMENTS, REP OUTLET WHEN MAKING REPLACEMENTS, REP OUTLET WHEN MAKING REPLACEMENTS, REP OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, AIRS, AIRS, AIRS, AIRS,
ADJUSTMENTS AND ADJUSTMENTS AND ADJUSTMENTS AND ADJUSTMENTS AND ADJUSTMENTS AND CONTINUITY CHECKS BEFORE CONTINUITY CHECKS BEFORE CONTINUITY CHECKS BEFORE CONTINUITY CHECKS BEFORE CONTINUITY CHECKS BEFORE
PROCEEDING WITH ANY REP PROCEEDING WITH ANY REP PROCEEDING WITH ANY REP PROCEEDING WITH ANY REP PROCEEDING WITH ANY REPAIR WORK. AFTER AIR WORK. AFTER AIR WORK. AFTER AIR WORK. AFTER AIR WORK. AFTER
DISCONNECTING, W DISCONNECTING, W DISCONNECTING, W DISCONNECTING, W DISCONNECTING, WAIT A AIT A AIT A AIT A AIT AT LEAST 1 MINUTE, UNTIL T LEAST 1 MINUTE, UNTIL T LEAST 1 MINUTE, UNTIL T LEAST 1 MINUTE, UNTIL T LEAST 1 MINUTE, UNTIL
THE CAP THE CAP THE CAP THE CAP THE CAPACITOR IN THE HIGH-VOL ACITOR IN THE HIGH-VOL ACITOR IN THE HIGH-VOL ACITOR IN THE HIGH-VOL ACITOR IN THE HIGH-VOLTTTTTAGE AREA AGE AREA AGE AREA AGE AREA AGE AREA
HAS FULL HAS FULL HAS FULL HAS FULL HAS FULLY DISCHARGED. Y DISCHARGED. Y DISCHARGED. Y DISCHARGED. Y DISCHARGED.
••••• WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH,
REPLACE WITH THE SAME TYPE SWITCH SPECIFIED
REPLACE WITH THE SAME TYPE SWITCH SPECIFIED REPLACE WITH THE SAME TYPE SWITCH SPECIFIED REPLACE WITH THE SAME TYPE SWITCH SPECIFIED REPLACE WITH THE SAME TYPE SWITCH SPECIFIED
ON THE P
ON THE P ON THE P ON THE P ON THE PAR AR AR AR ARTS LIST TS LIST TS LIST TS LIST TS LIST.....
A. A. A. A. A. REMOVING DOOR SENSING SWITCH REMOVING DOOR SENSING SWITCH REMOVING DOOR SENSING SWITCH REMOVING DOOR SENSING SWITCH REMOVING DOOR SENSING SWITCH
(Figures 1 on page 1, 10-a)
(1) Disconnect all wire leads from the Door Sensing
Switch. (Figure 1 on page 1)
(2) Remove 2 screws securing the Lever Stopper.
(3) Push the Door Sensing Switch upward while pressing
adjacent Upper Switch Stopper of Lever Stopper and
Lower Switch Stopper down (Figure 10-a).
(4) Then remove it by lightly pressing the switch toward
you (Figure 10-a).
(5) Make necessary adjustments or replacements of the
Door Sensing Switch by reversing step (3) and check
microwave energy leakage according to “1.
ADJUSTMENT PROCEDURES” on page 1, after it is
replaced with new one, and check proper operation
of it according to “CHECKOUT PROCEDURE FOR
SWITCHES” on page 6.
- 11 -
Door
Sensing
Switch
Upper
Switch
Stopper
Lower
Switch
Stopper
Figure 10-a Figure 10-a Figure 10-a Figure 10-a Figure 10-a
Primary
Interlock
Switch
Interlock
Monitor
Switch
Switch Stoppers
Figure 10-b Figure 10-b Figure 10-b Figure 10-b Figure 10-b
Switch Stoppers